A.O. Smith Cyclone BFC - 30 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 98

background image

Installation

38

Instruction manual BFC

3

is

9. Use the pressure gauge to read the supply pressure at 1nipple

(1)

(3.4.3 "Gas data")

.

Note

Consult the mains gas supply company if the supply pressure is not correct.

10. Use the pressure gauge to read the burner pressure at nipple

(2)

(3.4.3 "Gas data")

.

If the burner pressure is not correct and the appliance is fitted with a blank plate,
you will not be able to adjust the pressure. Finalise

(3.11.4 "Finalising")

, and in

this case, consult your installation engineer or supplier.
If the appliance is indeed fitted with a burner pressure regulator, the pressure can
be adjusted as described in the procedure

(3.11.3 "Adjusting the pressure")

.

3.11.3

Adjusting the pressure

1. Remove the cap (4) from the burner pressure regulator (3).
2. Correct the burner pressure by turning the adjusting screw (5), depending

on the correction required:
-

Adjustment screw anticlockwise: burner pressure decreases.

-

Adjustment screw clockwise: burner pressure increases.

3. Cover the opening of the adjusting screw and check the burner pressure

against the value given in the gas table

(3.4.3 "Gas data")

.

4. If the pressure is not set correctly, repeat the preceding steps until the

correct pressure is attained.

5. Fit the cap (4) back on the burner pressure regulator.
6. Activate the "OFF mode" of the electronic controller:

7. If the

MENU

is not displayed:

press .
-

Use and to place the cursor beside

OFF

.

-

Confirm with

.

8. Wait until the fan has stopped, and switch the electronic controller off.

Attention
Failure to wait until the fan stops can cause damage to the appliance.

9. Finish off

(3.11.4 "Finalising")

.

3.11.4

Finalising

1. Shut off the gas supply.
2. Disconnect the two pressure gauges and retighten the sealing screws in the

test nipples.

3. Replace the cover.

Note

Before starting-up the appliance, take time to fill in the warranty card

supplied with the appliance. This enables us to guarantee the quality of our
systems, and to further enhance our warranty procedure.
Please return this card as soon as possible. Your customer will then receive a
warranty certificate with our warranty conditions.

MENU

»OFF

^ ON

È WEEK PROGRAM

«
...
36
37
38
39
40
...
»

Содержание Cyclone BFC - 30



































































































Отзывы:

Нет отзывов

Похожие инструкции для Cyclone BFC - 30

Бренд: Qual Craft Страницы: 5

Бренд: L.B. White Страницы: 108

Бренд: EBARA Страницы: 16

Бренд: EBARA Страницы: 40

Бренд: EBARA Страницы: 38

Бренд: JBL Страницы: 12

Бренд: L.B. White Страницы: 28

Бренд: L.B. White Страницы: 68

Бренд: L.B. White Страницы: 34

Бренд: L.B. White Страницы: 28

Бренд: L.B. White Страницы: 4

Бренд: S&P Страницы: 18

Бренд: Orava Страницы: 19

Бренд: ICI Caldaie Страницы: 48

Бренд: Iguassu Ice Страницы: 16

Бренд: DAB Страницы: 72

Verderflex Vantage 5000 Series

Бренд: VERDER Страницы: 58

Бренд: DAYLIFF Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды