A.O. Smith Cyclone BFC - 30 Скачать руководство пользователя страница 36

Страница: 36 / 98

Installation

Instruction manual BFC

3.11 Checking the supply

pressure and burner
pressure

Note

Before starting the appliance and/or checking the supply pressure and

burner pressure, you must fill

(5 "Filling")

the appliance.

Attention

Before starting up for the first time or after conversion, you must always

check the supply pressure and burner pressure.

Note

The easiest way to check the gas pressures is by using two pressure

gauges. This procedure assumes that these two gauges are available.

Gas control

3.11.1

Preparation

To check the supply pressure and burner pressure, proceed as follows:
1. Isolate

(10.3 "Electrically isolating the appliance")

the water heater from the

power supply.

2. Undo the screws of the plastic covers.
3. Carefully remove the covers from the top of the appliance. The electrical

section is now visible.

Legend

Only applicable numbers are
mentioned.
1. supply pressure test nipple
2. burner pressure test nipple
3. burner pressure regulator
4. burner pressure control cap
5. burner pressure control

adjusting screw

IMD-0079a R2

Содержание Cyclone BFC - 30



































































































Результаты поиска

Содержание Cyclone BFC - 30

Отзывы:

Похожие инструкции для Cyclone BFC - 30

Бренды по названию

Популярные бренды

A.O. Smith Cyclone BFC - 30, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Cyclone BFC - 30

Отзывы:

Похожие инструкции для Cyclone BFC - 30

Бренды по названию

Популярные бренды