A.O. Smith Cyclone BFC - 30 Скачать руководство пользователя страница 28

Страница: 28 / 98

Installation

Instruction manual BFC

Explanation of type of appliance

Note

Make sure that the chimney discharges into an area where this is permitted

for this category of appliance.

3.9.3

Concentric connections

The table shows the requirements for concentric systems.

Warning

Install flue gas discharge pipe runs with a run-off of 5 mm per metre.

Flue gas discharge requirements for concentric systems (C13, C33)

Attention

Both conditions stated in the table must be fulfilled.

Even if there are less bends than the stated maximum, the maximum pipe
length may

not

be exceeded.

Even if the total pipe length is less than the stated maximum, the maximum
number of bends may

not

be exceeded.

The following example illustrates how to use the table.

Practical example of concentric flue gas discharge

Example

The figure shows a BFC 30 installation. The appliance must be fitted with 25 m
of concentric pipe (C13/C33) and four 90 degree bends. We need to check
whether this configuration complies with the requirements stated in the table.

Type of appliance

Description

B23

Air for combustion is drawn from the boiler room.

C13

Concentric and / or parallel wall flue terminal

C33

Concentric and / or parallel roof flue terminal

C43

Appliances on common air supply and flue gas discharge (concentric and / or

parallel) in multi-storey building.

C53

Air supply and flue terminal types mixed.

C63

Appliances supplied without flue components and / or terminal. These

appliances must be installed in compliance with local regulations.

Appliance

Diameter

Maximum length Maximum

number of 90º
bends

BFC 28

80/125 mm

40 m

BFC 30

100/150 mm

40 m

BFC 50

100/150 mm

40 m

BFC 60

100/150 mm

15 m

Содержание Cyclone BFC - 30



































































































Результаты поиска

Содержание Cyclone BFC - 30

Отзывы:

Похожие инструкции для Cyclone BFC - 30

Бренды по названию

Популярные бренды

A.O. Smith Cyclone BFC - 30, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Cyclone BFC - 30

Отзывы:

Похожие инструкции для Cyclone BFC - 30

Бренды по названию

Популярные бренды