A.O. Smith Cyclone BFC - 30 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 98

background image

Installation

18

Instruction manual BFC

3

is

3.3.1

Air humidity and ambient temperature

The boiler room must be frost-free, or be protected against frost. The table
shows the environmental conditions that must be adhered to for correct
functioning of the electronics present in the appliance to be guaranteed.

Air humidity and ambient temperature specifications

3.3.2

Appliance maximum floor load

In connection with the appliance's weight, take account of the maximum floor
loading, refer to the table.

Weight specifications related to maximum floor load

3.3.3

Water composition

The appliance is intended for heating drinking water. The drinking water must
comply with the regulations governing drinking water for human consumption.
The table gives an overview of the specifications.

Water specifications

Note

If the water specifications deviate from those stated in the table, then the

tank protection cannot be guaranteed

(16 "Warranty (certificate)")

.

3.3.4

Working clearances

For access to the appliance, it is recommended that the following clearances
are observed (see figure):
•

AA: around the appliance's control column and cleaning openings: 100 cm.

•

BB: all sides of the appliance: 50 cm.

•

Above the appliance (room to replace the anodes):
-

100 cm if using fixed anodes, or

-

50 cm if using flexible anodes.

Air humidity and ambient temperature

Air humidity

max. 93% RV at +25°C

Ambient temperature

Functional: 0 < T < 60°C

Weight of the appliance filled with water

BFC 28

394 kg

BFC 30, BFC 50, BFC 60

582 kg

Water composition

Hardness

(alkaline earth ions)

> 1.00 mmol/l:
•

German hardness> 5.6° dH

•

French hardness > 10.0° fH

•

English hardness > 7.0° eH

Conductivity

> 125 µS/cm

Acidity (pH value)

7.0 < pH value < 9.5

«
...
16
17
18
19
20
...
»

Содержание Cyclone BFC - 30



































































































Отзывы:

Нет отзывов

Похожие инструкции для Cyclone BFC - 30

Бренд: ABI Attachments Страницы: 20

Бренд: NARVI Страницы: 12

Бренд: Waterous Страницы: 10

Бренд: Oasis Страницы: 18

Бренд: Jandy Страницы: 108

Бренд: Jandy Pro Series Страницы: 40

Бренд: Oasis Страницы: 14

Elmo Rietschle V-VC 40

Бренд: Gardner Denver Страницы: 32

Бренд: Desa Страницы: 20

Бренд: Zibro Страницы: 28

Бренд: Wilo Страницы: 76

Бренд: Webasto Страницы: 12

Бренд: Rheem Страницы: 48

Бренд: nedis Страницы: 36

Бренд: VEAB Страницы: 4

Бренд: Oceanic Страницы: 33

Ambiance B9945N

Бренд: United States Stove Страницы: 28

PERFECT 350 ELECTRONIC

Бренд: Wijas Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды