19
COMMAND CODES
These are the command codes used with the ANI-MOD Matrix control software, included with the unit. With this command system, users are
able to control and operate the ANI-MOD Matrix remotely via the RS-232 connection and the appropriate software.
Command Types Command Codes Functions
/*Type;
Inquire the model’s information.
/%Lock;
Lock the keyboard of the control panel on the Matrix.
/%Unlock;
Unlock the keyboard of the control panel on the Matrix.
/^Version;
Inquire the version of
fi
rmware that the Matrix has installed
/:MessageOff;
Turn off the feedback command from the com port. It will only show the “switcher OK.”
/:MessageOn;
Turn on the feedback command from the com port.
Undo.
To cancel the previous operation.
Demo.
Switch to the “demo” mode, 1->1, 2->2, 3->3 … and so on.
[x1]All.
Transfer signals from one particular input channel [x1] to all output channels
All#.
Transfer all input signals to the corresponding output channels respectively.
All$.
Switch off all the output channels.
[x1]#.
Transfer signals from the input channel [x1] to the output channel [x1].
[x1]$.
Switch off the output channel [x1].
[x1] V[x2].
Transfer the video signal only the input channel [x1] to the output channel [x2].
[x1] V[x2],
[x3], [x4].
Transfer the video signal only the input channel [x1] to the output channels [x2], [x3] and [x4].
[x1] A[x2].
Transfer the audio signal only the input channel [x1] to the output channel [x2].
[x1] A[x2],
[x3], [x4].
Transfer the audio signal only the input channel [x1] to the output channels [x2], [x3] and [x4].
[x1] B[x2].
Transfer signal from the input channel [x1] to the output channel [x2].
[x1] B[x2],[x3],[x4]. Transfer signal from the input channel [x1] to the output channels [x2], [x3] and [x4].
[x1].
Allows you to inquire what source channel is supplying signal to the output channel [x1].
Status.
Allows you to inquire what input channels are supplying signal to all of the output channels.
This information will be provided on a one by one basis (1x3, 2x2, 3x8), where the
fi
rst
number is the destination channel and the second number is the source channel.
Save[Y].
Save the present operation to the preset command [Y]. [Y] ranges from 0 to 9.
Recall[Y].
Recall the preset command [Y].
Clear[Y].
Clear the preset command [Y].
EDIDMInit.
Recover the factory default EDID (extended display identi
fi
cation data) data.
EDIDM[X]B[Y].
Manual EDID management. Copy the EDID data of output[X] to the input[Y].
PWON.
Set the Matrix to normal working status
PWOFF.
Set the Matrix to stand-by status.
HDCPON.
Turn on the HDCP (high-bandwidth digital content protection) output.
HDCPOFF.
Turn off the HDCP output.
PTN/I/[X]:0622%;
Set the input channel [x] to support VGA signal input. (NOTE 4)
PTN/I/[X]:0623%;
Set the input channel [x] to support YPbPr signal input. (NOTE4)
PTN/I/[X]:0624%;
Set the input channel [x] to support SVIDEO signal input. (NOTE1)
PTN/I/[X]:0625%;
Set the input channel [x] to support CVIDEO signal input. (NOTE 4)
PTN/I/[X]:0626%;
Scale the resolution of input [x] to 1024*768. (NOTE 4)
PTN/I/[X]:0627%;
Scale the resolution of input [x] to 1280*720. (NOTE 4)
PTN/I/[X]:0628%;
Scale the resolution of input [x] to 1280*800. (NOTE 4)
PTN/I/[X]:0629%;
Scale the resolution of input [x] to 1920*1080. (NOTE 4)
System Command
Operation Command
ANI-MOD88 ONL
Y
