manualshive.com logo in svg

3M UniPresser 3M710, Инструкция по эксплуатации

Поделиться
Скачать
3M UniPresser 3M710 Скачать руководство пользователя страница 12

 DOCUMENT

 OBSOLETE

12

78-8125-3042-2-B

With the “T” bar in the “Up”
position, use the hex nut wrench
(fig. 4 #5) to remove the four
(4) screws (fig. 2 #3) at the rear
of the uni-presser head.

With the”T” bar in the open
position loosen two (2) screws
(fig.3 #3) on the front cover of
the unipresser head. (DO NOT
REMOVE THE SCREWS.)

3M

™

Uni-Presser Blade Replacement

Old Blade Removal

Apply thumb pressure and remove
old blade assembly. (fig. 1 #11)

Blade and holder is a one piece unit.

(fig. 4 #1)

New Blade Replacement

A

While holding back the blade
guard (fig. 2 #15) use finger
pressure on the metal ends and
insert the new unit into the “T”
bar. Caution: Sharp blades -
do not touch the cutting
blades. (fig. 1#11)

Starting at the center of the “T”
bar, line up the new matching
one (1) blade to one (1) stuffer.

With the :”T” bar in the open
position, tighten the two (2)
screws (fig. 3 #3) on the front
cover enough to secure the
blade unit inside the head.

BLADE FRONT
FACING UP

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

Содержание UniPresser 3M710

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды