manualshive.com logo in svg

3M UniPresser 3M710, Инструкция по эксплуатации

Поделиться
Скачать
3M UniPresser 3M710 Скачать руководство пользователя страница 10

 DOCUMENT

 OBSOLETE

10

78-8125-3042-2-B

29. To remove the module, push the “L” clip
(fig. 1 #9) in and lift clear of Uni-Presser. The
half tapped module is now complete.

30. Use a conductor wire cut off tool to remove
the old cable. Position the tool on the connector
to cut against the wire lay. A no break cable
transfer has been completed.

31. After the old conductors have been removed, fit
a half-tap cover. Remove the plastic protection from
the strip of sticky tape inside cover. This sticky tape
is positioned against the removed conductor ends as
the cover is snapped onto the module.

32. 3M710 25-pair connector module with half-tap
cover in position

Bridge Splicing

Basic Technique for Bridge Splicing 3M

™

3M710 25-Pair Modules

33. Position a 3M710 red bridge
module support (fig.4 #3)
between the vertical side posts
(fig. 1 #2) with the word FRONT
facing the operator/”T” bar. Push
the “L” clip button inward,
(fig. 1 #9 and release to secure
the support in position.

34. Position a bridge module into
the red bridge module support.
Hand seat the module firmly
with the peak colors matching
the color code check strip (fig.1
#10) and cathedral windows fac-
ing forward/front.

35. Dress the conductors into the
bridge module in color code
sequence.

Repeat steps 16

through 22.

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

Содержание UniPresser 3M710

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды