manualshive.com logo in svg

3M UniPresser 3M710, Инструкция по эксплуатации

Поделиться
Скачать
3M UniPresser 3M710 Скачать руководство пользователя страница 11

 DOCUMENT

 OBSOLETE

11

78-8125-3042-2-B

36. Remove the bridge module
from the red bridge support with
gentle upwards pressure. The
bridge module is now complete.

37. Carefully insert the bridge
module into the through cable
connector at the rear bridge
entry ports. Use a Bridge Splice
Presser  Tool along the length of
the module to securely seat the
bridge and contacts.

38. The latches of the bridge
module should face the cap of
the “trough module”.

3M

™

Bridge Module Splice Installation

Bottomless Splicing

Basic Technique for Bottomless Splicing 3M

™

3M710 25-Pair Modules

39. Position a 3M710 bottomless
splice module support (fig. 4 #4)
between the vertical side posts. (fig. 1
#2). The large gaps go to the rear and
accommodate the “L” clips. (fig 1
#8). Push the “L” clip button (fig. 1
#9) to tightly seat the module support.

40. Position a straight/half-tap
module body onto the bottomless
support between the side posts.
Hand seat the module only. The
latches fit into the cuts and face
the operator.

41. Dress the conductors into the
module in color code sequence.

Repeat steps 16 through 22.

42.

Remove the bottomless splice

from the bottomless support 
module. The bottomless splice is
now  complete.

43. With a bridge splice presser
seat the module onto an index
strip with the wires seated
“through” for a half-tap.

44. Use a conductor wire cut-off
tool to remove the old cable parts.

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

 DOCUMENT

 OBSOLETE

Содержание UniPresser 3M710

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды