3M 5458A-IJ Скачать руководство пользователя страница 8

Страница: 8 / 16

78-8127-8872-3-

4.2 If using cold shrink adapter tube:

Position adapter tube over the connector. Shrink adapter near center of

connector by pulling and unwinding the loose core end in a counter-clockwise direction

(Figure 13).

Cold shrink adapter tube

Figure 13

4.3 Clean cables using standard practice:

a. Do not allow solvent or abrasive to contact the cable semi-conductive insulation shield.

b. Do not reduce cable insulation diameter below 1.24" (31,5 mm) specified for the splice.

c. The insulation surface must be round, smooth and free of cuts/voids. Sanding may be necessary, finish

sanding should be done with a 300 grit or higher electrical grade abrasive.

d. Make certain that the cable insulation is smooth, clean and dry before continuing.

4.4 Apply red compound on cable insulations, making certain to fill in edge of cable semi-con.

Do not use

silicone grease

(Figure 14).

Apply Red

Compound

Apply Red

Compound

Fill semi-con step

Figure 14

Содержание 5458A-IJ

















Результаты поиска

Содержание 5458A-IJ

Отзывы:

Похожие инструкции для 5458A-IJ

Бренды по названию

Популярные бренды

3M 5458A-IJ, Инструкция по эксплуатации

Результаты поиска

Содержание 5458A-IJ

Отзывы:

Похожие инструкции для 5458A-IJ

Бренды по названию

Популярные бренды