3M 5458A-IJ Скачать руководство пользователя страница 2

Страница: 2 / 16

78-8127-8872-3-

1.0 Kit Contents

a. 3M

™

Cold Shrink Integrated Splice Body 5458A-IJ (1 ea.)

b. Constant Force Springs (4 ea.)
c. Red Compound Tubes (non-silicone grease) (2 ea.)
d. Scotch

Rubber Mastic Tape 2228 Rolls, 2" x 48" (2 ea.)

e. Scotch

Mastic Sealing Strips 2230, 6" length (8 ea.)

f. Cold Shrink Adapter Tube (1 ea.*)
g. 3M

™

Cable Cleaning Pads CC-3 (1 ea.)

h. Scotch

Electrical Shielding Tape 24, 1" x 15' ( 1 ea.)

i. 3M

™

Aluminum Foil Tape Strips 1115B, 10" length (2 ea.)

j. Cut-back Template (2 ea.**)
k. Instruction Booklet (1 ea.)

*Cold shrink adapter tube may not be included in all kits.

**Kits contain either 1 or 2 cut-back templates as needed per conductor size.
Note: Do not use knives to open plastic bags.
Note: Connector not shown, but if included, it is indicated on the packaging label.

Содержание 5458A-IJ

















Результаты поиска

Содержание 5458A-IJ

Отзывы:

Похожие инструкции для 5458A-IJ

Бренды по названию

Популярные бренды

3M 5458A-IJ, Инструкция по эксплуатации

Результаты поиска

Содержание 5458A-IJ

Отзывы:

Похожие инструкции для 5458A-IJ

Бренды по названию

Популярные бренды