3M 3M-Matic Dual S-867 II Скачать руководство пользователя страница 6

Страница: 6 / 62

Important Safeguards

This safety alert symbol identifies
important messages in this

manual. READ AND UNDERSTAND
THEM BEFORE INSTALLING OR
OPERATING THIS EQUIPMENT.

Explanation of Signal Word Consequences

Indicates a potentially hazardous
situation, which, if not avoided,
could result in death or serious
injury and/or property damage.

WARNING:

Indicates a potentially hazardous
situation, which, if not avoided,
may result in minor or moderate
injury and/or property damage.

CAUTION:

•

To reduce the risk associated with sharp

blade hazards:

−

Keep hands and fingers away from tape cutoff

blades under orange blade guards. The
blades are extremely sharp

•

To reduce the risk associated with muscle

strain:

−

Use the appropriate rigging and material

handling equipment when lifting or
repositioning this equipment

WARNING

(continued)

•

To reduce the risk associated with pinch

and entanglement hazards:

−

Always feed boxes into the machine by

pushing only from the end of the box

−

Keep hands, hair, loose clothing, and jewelry

away from opening in the nest

CAUTION

•

To reduce the risk associated with

mechanical and pneumatic hazards:

−

Read, understand and follow all safety and

operating instructions before operating or
servicing the case sealer

−

Allow only properly trained and qualified

personnel to operate and/or service this
equipment

−

Never attempt to defeat the machine guard

interlock

•

To reduce the risk associated with pinch

and entanglement hazards:

−

Turn air supply off and disconnect before

performing any adjustments, maintenance or
servicing the machine

−

Turn the machine off while not in use

−

Never attempt to work on any part of the

machine or load tape while the machine is
running

WARNING

Important –

In the event the following safety

labels are damaged or destroyed,

they must

be replaced to ensure operator safety

Replacement part numbers for individual
labels are shown in "Important Safeguards,"
at the beginning of Section II.

Содержание 3M-Matic Dual S-867 II































































Результаты поиска

Содержание 3M-Matic Dual S-867 II

Отзывы:

Похожие инструкции для 3M-Matic Dual S-867 II

Бренды по названию

Популярные бренды

3M 3M-Matic Dual S-867 II, Инструкция и перечень запасных частей

Результаты поиска

Содержание 3M-Matic Dual S-867 II

Отзывы:

Похожие инструкции для 3M-Matic Dual S-867 II

Бренды по названию

Популярные бренды