3M 3M-Matic Dual S-867 II Скачать руководство пользователя | Manualshive

Страница: 36 / 62

background image

16

Operation

(Continued)

3.

Bring the tape up over the take-up roller, adhesive
side up.

7.

Turn “on” the main air supply at the on/off valve.

8.

To clear the tape which has been tacked to the
nest, manually holding the paddle stop down
and push the box paddle in to cycle the unit.
The applicator is ready to operate.

4.

Thread the tape over the top wrap roller, around
the one way roller assembly, over the wrap roller,
adhesive side toward the nest, begin tape down
behind the tape holding roller and also the tape
pick-up roll.

Note: To simplify the tape threading at the
next reloading, replace with a new roll of
"Scotch" brand filament tape, and splice the
tape web together at the tension roller.

5.

Pull out enough tape to tack it to the top of the
nest as shown.

6.

Close the cover and secure the latch.

Note: Remove all work tools, etc. from inside
S-867 case before closing cover.

Operating Sequence

1.

Move the box forward over the paddle stops,
depressing the box paddle and hold it firmly and
squarely against the nest vertical surface to apply
the tape.

2.

The application only takes 1/4 second to apply
the tape, then the box can be removed from the
nest while the machine continues to complete the
cycle.

•

To reduce the risk associated with

sharp blade hazards:

−

Keep hands and fingers away from tape

cutoff blades under orange blade guards.
The blades are extremely sharp

WARNING

•

To reduce the risk associated with pinch

and entanglement hazards:

−

Keep hands, hair, loose clothing, and jewelry

away from the opening in the nest

CAUTION

•

To reduce the risk associated with pinch

and entanglement hazards:

−

Always feed boxes into the machine by

pushing only from the end of the box

CAUTION

«
...
34
35
36
37
38
...
»

Содержание 3M-Matic Dual S-867 II































































Отзывы:

Нет отзывов

Похожие инструкции для 3M-Matic Dual S-867 II

Бренд: Rotel Страницы: 5

Бренд: Rotel Страницы: 5

Бренд: Technics Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды