3M 3M-Matic Dual S-867 II Скачать руководство пользователя

Страница: 41 / 62

Troubleshooting

(Continued)

Troubleshooting Guide

(arranged in sequence of machine operation)

Possible Cause

1. Valve V-4 out of adjustment or

defective.

2. Flow control closed.

3. Power valve P-2 defective.

1. Valve V-3 out of adjustment or

defective.

2. Valve V-2 out of adjustment or

defective, sticks closed when box
paddle is actuated.

1. Valve V-6 out of adjustment or

defective.

2. Valve V-5 out of adjustment or

defective.

3. Power valve P-2 defective.
4. Valve V-7 out of adjustment or

defective.

1. Valve V-7 out of adjustment or

defective.

2. Valve V-5 out of adjustment or

defective.

3. Check for loose cylinder rod

connection.

1. Dull blade.
2. Blade out of adjustment.

1. Bad jaw roller.
2. Valve V-6 actuates before tape is in

jaw assembly.

3. Valve V-7 actuated before tape is

clamped.

4. Wave washer (Item #81) missing from

tape holding roller (Item #27).

5. Jaws close too slow.

6. Feed cylinder extends too fast.

7. Low clamping force on tape. Missing

or broken jaw spring (Item #114).

8. Bad one-way roller assembly. End of

tape is not fed into the jaw assembly.

Problem

Cut-off assembly and buffing assembly
cycle extend and retract and unit stops.

Buffing arm/cut-off blade out of sequence,
oscillate back and forth.

Feed assembly retracts and stops.

Feed cylinder extends but does not
actuate V-8 valve.

Tape not cutting or tape end shredding or
buffing rollers stop in mid-stroke and do
not apply the tape.

Tape not being held by jaw assembly.

Correction

1. Adjust or replace valve V-4.

2. Adjust extend flow control for feed

cylinder.

3. Replace valve.

1. Turn off air supply adjust valve V-3.

Retract cut and buffing cylinder to
retracted positions. Actuate and hold
V-3 as air is turned on. This should put
air circuitry in sequence.

2. Adjust or replace valve V-2.

1. Adjust or replace valve V-6.

2. Adjust or replace valve V-5.

3. Replace valve.
4. Adjust or replace valve V-7.

1. Adjust or replace valve V-7.

2. Adjust or replace valve V-5.

3. Retighten and adjust V-8 valve if

needed.

1. Replace blade.
2. Readjust blade and tighten screw.

1. Replace roller.
2. Adjust V-6 valve.

3. Adjust or replace V-7 valve.

4. Replace wave washer.

5. Adjust jaw cylinder flow control.
6. Adjust flow control for extending feed

cylinder.

7. Replace jaw spring.

8. Replace one-way roller assembly

located on feed assembly.

•

To reduce the risk associated with sharp blade hazards:

−

Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are extremely

sharp

•

To reduce the risk associated with mechanical and pneumatic hazards:

−

Allow only properly trained and qualified personnel to operate and/or service this equipment

•

To reduce the risk associated with pinch and entanglement hazards:

−

Turn air supply off and disconnect before performing any adjustments, maintenance or servicing the machine

WARNING

Содержание 3M-Matic Dual S-867 II































































Результаты поиска

Содержание 3M-Matic Dual S-867 II

Отзывы:

Похожие инструкции для 3M-Matic Dual S-867 II

Бренды по названию

Популярные бренды

3M 3M-Matic Dual S-867 II, Инструкция и перечень запасных частей

Результаты поиска

Содержание 3M-Matic Dual S-867 II

Отзывы:

Похожие инструкции для 3M-Matic Dual S-867 II

Бренды по названию

Популярные бренды