3D Systems Fiure 4 Standalone, Руководство пользователя, Страница: 26 / 120

8/12/22, 2:53 PM Руководство пользователя
ru.infocenter.3dsystems.com/figure4jewelry/print/book/export/html/526 26/120
The Figure 4 Jewelry Printer is 34.5 kg (76 lbs) and does not require a table rated for a heavy load. Additional equipment, such as a UV oven or
ultra-sonic cleaner, will each have their own loads for your setup to bear. Refer to the
Weights and Measures Charts to determine the total
weight of the equipment to be housed in your room to ensure that you do not exceed the maximum load-bearing capacity that your printer-
staging area can support.
Требования к электропитанию
Electrical voltage requirements for the Figure 4 Jewelry Printer:
120–240 В , 50/60 Гц , 4 А (2 А для Европы ), 1 фаза
Power for the Figure 4 Jewelry Printer should be on a surge-protected circuit. 3D Systems does not require the use of a UPS (Uninterruptible
Power Supply) for the Figure 4 Jewelry Printer. However, if you live in an area with frequent power surges/outages, a UPS would be useful to
prevent a build from crashing in the event of a brief power outage/surge.
Ensure that the space you select for the printer has a power outlet reachable by the length of cord the comes with the printer. Use of an
extension cord or power strip is not recommended.
Если кабель питания повреждается или утрачивается , необходимо заказать в 3D Systems кабель питания на замену , по своим
характеристикам подходящий для вашего устройства . Не используйте кабель питания , который не предназначен для принтера .
Компания 3D Systems укажет , какие компоненты должны осматриваться или предоставляться только 3D Systems или ее партнерами .
Часть 2
Рассеивание тепла
The Figure 4 Jewelry Printer is not expected give off signi cant heat under normal operating conditions.
Подключение к сети переменного тока
В США необходимо использовать стандартную настенную розетку на 10 А . Система подключается к розетке 120 В переменного тока
посредством стандартного кабеля питания 120 В .
В Европе необходимо использовать стандартную настенную розетку на 10 А . Система подключается к розетке 230 В переменного тока
посредством стандартного кабеля питания 230 В . В наличии имеются специальные комплекты для подключения к розетке в конкретной
стране использования системы .
Температура
Температура в помещении , где располагается принтер Figure 4 Standalone, должна быть стабильной для обеспечения оптимальной
работы системы и высокого качества напечатанных деталей .
Figure 4 print materials should be stored between 5°C-30°C (41°F-86°F). However, successful printing has only been tested at a minimum of
18°C (64.4°F) and a maximum of 28°C (82.4°F). If your room is kept beyond either extreme, you may see a degradation in print quality.
Влажность
The optimal humidity in the Figure 4 Jewelry build chamber and lab will depend to a certain degree on the Figure 4 material selection.
Regardless, the humidity should always be non-condensing and should not vary outside the range of 30 to 70% RH. Review your Figure 4
material information (SDS, User Guide, and product labeling) for speci c information on recommended humidity levels.
Высота
The Figure 4 system is capable of operating correctly up to an altitude of 2,400 m (7,874 ft.) above mean sea level.
Вентиляция
Venting printer fumes outside is not required. Your HVAC system should perform at least six air exchanges per hour in the room where the
printer is located. You may wish to have a fume hood installed for your part-cleaning area. Ensure that your facility complies with all local and
regional regulations regarding ventilation of vapors, dust, and other by-products of printing, cleaning and secondary processing. Always refer to
and follow the information on the SDS for your speci c material.
Часть 3