3B6 SLIM Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 31

3B6 SLIM Скачать руководство пользователя страница 3

WARRANTY

THERE  ARE  NO  WARRANTIES,  EXPRESSED  OR  IMPLIED,  MADE  BY  EITHER  THE
DISTRIBUTOR  OR  THE  MANUFACTURER  ON  NEW  3B6  SYSTEMS  AND
COMPONENTS,  EXCEPT  THE  MANUFACTURER’S  WARRANTY  AGAINST  DEFECTS,
MATERIAL AND WORKMANSHIP SET OUT BELOW.

NEW EQUIPMENT WARRANTY

“The  manufacturer  warrants  each  new  product  made  by  the  manufacturer  to  be  free  from
defects in material and workmanship, its obligation and liability under this warranty being
limited to replacing free of charge at its factory any part proving defective under normal use
and service within twelve (12) months from the date of initial sale, providing the product is
on record with the manufacturer as being installed by the distributor. If the product is not on
record  as  being  installed  by  the  distributor,  the  manufacturer  will  consider  the  date  of
shipment  from  the  factory  as  the  date  of  initial  sale.  This  warranty  is  in  lieu  of  all  other
warranties, expressed or implied and the obligation and liability of the manufacturer under
this warranty shall not include any transportation or other charges or the cost of installation
or  any  liability  for  direct,  indirect  or  consequential  damages  or  delay  resulting  from  the
defect.  Any  operation  beyond  rated  capacity  or  the  improper  use  of  the  product  or  the
substitution upon it of parts not approved by the manufacturer shall void this warranty. This
warranty covers only the products of 3B6. The products of other manufacturers are covered
only by such warranties as made by their manufacturers.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED
OR  IMPLIED,  INCLUDING  ANY  IMPLIED  WARRANTY  OF  MERCHANTABILITY  OR
FITNESS  FOR  A  PARTICULAR  PURPOSE,  AND  OF  ANY  OTHER  OBLIGATIONS  OR
LIABILITY  OF  THE  PART  OF  THE  MANUFACTURER,  AND  3B6  NEITHER  ASSUMES
NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY
IN CONNECTION WITH SUCH EQUIPMENT.

3B6

Troubleshooting Manual

«
1
2
3
4
5
...
»

Содержание SLIM
































Отзывы:

Нет отзывов