3B6 SLIM Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 31

3B6 SLIM Скачать руководство пользователя страница 16

16

System Alarm Codes

ALARM 16 Shutoff output circuit not verified

Faulty wiring
Internal fault SLIM display Check wiring from harness to shutoff valves
Call Service

ALARM 22 Output supply not verified

Check wiring from harness to shutoff valves
Call Service

ALARM 41 CRC Error in SW running

Internal fault SLIM display
Cycle power on SLIM display, Call Service

ALARM 42 CRC Error EPROM SW program

Internal fault SLIM display
Cycle power on SLIM display, Call Service

ALARM 43 CRC Error in EPROM load chart pages

Internal fault SLIM display Cycle power on SLIM display, Call Service

ALARM 50 Cable reel CANBUS lost

Check +12 vdc inside cable reel
Check wiring from harness to cable reel
Check angle sensor is functioning
Check for 120 ohm resistor between CAN H and CAN L lines

ALARM 60 A2B Condition

Faulty wiring
Check wiring from harness to Cable reel and A2B switch

ALARM 61, 62, or 63 LMI Overload

Exceeded rated capacity, Reduce capacity or radius
Cylinder topped

ALARM 64 Bypass enabled

Faulty wiring
Check wiring from harness to bypass
Call Service

Alarm 70 Rotation pot ADC value

Check wiring to rotation pot

Alarm 71 Rotation prox switch

Check wiring to pot
Check mechanical hardware on pot.

Alarm 72 Rotation pot malfunction

Check wiring to pot
Check voltage supply to pot +5vdc
Check pot output with boom directly over rear should be 2.50 vdc
Check display diagnostics P10
Replace pot

3B6

Troubleshooting Manual

«
...
14
15
16
17
18
...
»

Содержание SLIM
































Отзывы:

Нет отзывов