3B6 SLIM Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 31

3B6 SLIM Скачать руководство пользователя страница 2

3B6

Troubleshotting Manual

WARNING

The SLIM system is an LMI, with Range limiting
features.

The system should be checked for the shutoff
functions prior to programming the Operating mode
and confirming by trying to move the boom functions
to ensure the shutoff is disabled.

A full check confirming all features on the system are
functioning properly prior to lifting any loads!

To obtain the optimum performance from this system
we recommend that you read and understand this
manual before using the system.

WARNING

For proper use of the system, carefully read and understand this page.

MAINTENANCE

The SLIM system power cable must be

                               disconnected when welding, battery replacement, charging or jump
                               starting the battery. Failure to comply will result in serious damage to
                               the system.

MACHINE WASHING

If washing the machine with a high pressure power washer, you

must protect all the system components from direct spraying to
avoid damage to the components.
Failure to comply with the above warnings will result in voiding the warranty!

Introduction

«
1
2
3
4
...
»

Содержание SLIM
































Отзывы:

Нет отзывов