background image

16

17

2VV.

 Creating innovative solutions for you and your business since 1995.

The settings can be found below, under 

“SUBUNITS”

Current status

Settings MENU

Required temperature 

settings with closed doors

Air flow settings with clo

-

sed doors

Date and time settings

This screen show the detailed status of the opening and the sensor values:

• 

Current air-flow settings (step or %), information icons

• 

Air temperature at intake*, exhaust*, room temperature* and outside temperature* (* – if the relevant sensors are installed and enabled)

• 

Heater output settings (if included)

The information on any connected SLAVE units will be shown here.
It can be accessed moving the screen upwards.

Required temperature 
settings
(with closed doors)

Air flow settings

(with closed doors)

Language

Display backlight

Parameters

Date and 
time

App

Back to previous 
screen

Confirm

+ return

Confirm

+ return

Display required air flow (20% 

steps)

Reduce or increase 

opening’s air flow (with 

closed doors)

Display the 

current air flow 

status

Current date and time

Reduce or increase 
required tempe-
rature

Actual temperature 
at selected sensor in 
menu 09

Required output

Manual mode = %

Automatic mode = °C

If the heating is blocked in summer mode 
(MENU - SUMMER HEATING), the screen will show a 
“Sun” icon and will not allow to select the output.

Confirm

+ return

Back to main screen

Information on 
the type of unit

Indicates heating is blocked 
(summer mode)

Back to previous 
screen

Green color = active sensor

SP= Temperature setpoint

Room temperature

Inlet temperature

Outside temperature

Fan speed

Heat power

Return water temperature

7. CONTROL

Содержание IC3-C-AC5-04






























Отзывы: