2N Netstar Скачать руководство пользователя страница 41

Страница: 41 / 282

DSS1 protocol parameters

Reverse mode NT/TE

– this option refers to L3 signalling only. Check this

option to make a TE port behave as an NT port (and vice versa).

Do not send time at NT

– use this option to disable sending of the connection

date and time information within the CONNECT message from an NT port to a TE
port. Available for NT ports only.

Ignore unset explicit channel

– use this option to enable call establishment

without an explicitly set B–channel.

Always select B–channel

– use this option to disable sending the Channel

identification information within the SETUP message with channel signalling.
Available for TE ports only.

Disconnect L2 if no call

– use to disconnect the L2 layer on an inactive

interface. The PBX automatically disconnects the layer after a

. An

timeout

incoming call automatically reconnects the layer.

Keep L2 connected

– check this option to make the PBX keep the L2 layer

connected on this interface without any incoming call. This option may not be
combined with the

option.

Disconnect L2 if no call

Disconnected L2 as error

– use this option to activate a caution about the

second layer being disconnected. This fact is indicated by a red exclamation mark
on the port in the

menu and a red text in the upper stack

Hardware – Boards

status field. This option may not be combined with the

Disconnect L2 if no call

option.

Terminals

– not applied for PRI ports.

is able to process (i.e. resend to an interface other than

2N NetStar

ISDN) only

G.711 A-law

encoded calls on the ISDN interface. Calls

encoded by

G.711 µ-law

can only be resent between the ISDN

interfaces in the PBX.

Digital interface diagnostic

Line state

– the parameter cannot be set. It only shows the state of the first

interface layer.

Number of SLIPs per minute

– this parameter gives the count of slips. A slip is

caused by different clocks of the PBX and the active terminal. This value is
updated every 6 seconds and represents a weighted average per minute.

Bit error rate per second

– the BER parameter gives a count of incorrectly

transferred bits during transmission. The value is updated every 6 seconds and
represents a weighted average per minute.

If the

port supervision is used, enable some or all of the following parameters:

SNMP

Inactive L1 as error Disconnected L2 as error Nonsynchronous L1 as error

. If not, the port error will not be detected and the PBX will be unable to

BER as error

send a warning.

Содержание Netstar



























































































































































































































































































Результаты поиска

Содержание Netstar

Отзывы:

Бренды по названию

Популярные бренды

2N Netstar, Руководство пользователя

Результаты поиска

Содержание Netstar

Отзывы:

Бренды по названию

Популярные бренды