manualshive.com logo in svg

2N Netstar, Руководство пользователя

Поделиться
Скачать
2N Netstar Скачать руководство пользователя страница 234

234

including these parameters.

No  port

  –  use  this  option  to  set  routing  rules  for  the  extensions  that  are  not

assigned  to  any  port.  Such  extensions  include,  in  particular,  PBX  external  or
virtual port extensions used for special routing cases.
For call routing by the PBX refer to the 

 chapter.

Routers

Parameters of unsuccessful sending
Repeat  at  fail

  –  use  this  option  to  enable  repeating  of  a  failed  SMS  sending

attempt.  An  attempt  may  fail  due  to  a  GSM  network  rejection  or  bad  signal
quality.  This  option  does  not  refer  to  SMS  delivery  failures  due  to  switch–off  or
temporary unavailability of a remote GSM extension.

Number of repeated attempts

 – use this parameter to set the maximum count

of  sending  attempts  at  an  SMS  sending  failure  due  to  network  rejection  or
temporary signal unavailability. The default value is 4000.

Time for message repeat [s]

 – use this parameter to set the interval between

successive SMS sending attempts. The default value is 180s.

ME

The  ME  subtag  is  used  for  setting  parameters  for  external  extensions.  They  mostly
include parameters for call holding using an external extension. Mobile phones are not
equipped with a standard PBX call holding key and that is why this function has to be
replaced with a sequence of DTMF symbols. This tag contains the following parameters:

Transfer

 – use this parameter to enable call holding from an external extension.

This function is subject to licence and hierarchy. If you define this parameter on
the user level, you need as many licences as many extensions the user has (the
external extension is not included because it needs licence for use).

Pattern  time  interval  [ms]

  –  use  this  parameter  to  set  the  time  interval

between individual characters of the FLASH and DISCONNECT patterns. This time
interval is important for a correct recognition of the pattern. If the delay between
the pattern characters is longer than the preset time value, the pattern will not
be recognised.

FLASH pattern

 – use this parameter to set the sequence of the FLASH pattern

characters used for call holding. Re–enter the FLASH pattern to reconnect a held
call or switch between two calls (one active and one on hold).

DISCONNECT  pattern

  –  use  this  parameter  to  set  the  sequence  of  the

DISCONNECT pattern characters. When you have one active call and one call on
hold, use this pattern to terminate the active call and reconnect the call on hold.

Do not end outgoing call

 – use this parameter to select that an outgoing call

from  the  PBX  to  an  external  station  shall  not  be  terminated  after  the  calling
subscriber hangs up. Instead, the user gets the busy tone from the PBX and can,
using  the  DISCONNECT  PATTERN,  return  to  the  dialtone  and  dial  the  required
station through the PBX. The selection is disabled by default.

Do not end incoming call

 – use this parameter to select that an incoming call

from  an  external  station  to  the  PBX  shall  not  be  terminated  after  the  calling
subscriber hangs up or the DISA fails. Instead, the user gets the busy tone from
the  PBX  and  can,  using  the  DISCONNECT  PATTERN,  return  to  the  dialtone  and
dial the required station through the PBX. The selection is disabled by default.

Forwarding

The whole tag is available on the group and user levels only.

This subtag is used for call forwarding setups. The unconditional call forwarding (CFU)
has  the  highest  priority.  The  other  two  forwarding  types  have  the  same  priority  and

Содержание Netstar



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды