CS400 DIRECTSTART
REMOTE CAR S ALARM
CS400 VERSION 412
9
WIRE HARNESS DESCRIPTION
J1: 6 PIN MAIN WIRING HARNESS
PIN#
PIN#
PIN#
PIN#
COLOR
COLOR
COLOR
COLOR
POLARITY
POLARITY
POLARITY
POLARITY
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
J1-PIN#1- RED(30A FUSE) : + 12 VDC Main Power Source Input
: Connect the
Red
wire to main constant
+12 VDC power source or to the positive terminal of the battery. If there are two constant 12 volt sources at
the ignition switch, then the RED input wires must be connected to a one source each.
J1-PIN#2- GREEN: + Accessory Output (Heater/ A/C
) :Connect this
Green
wire to the accessory wire which
su12VDC when the ignition key is in the ignition
"on"
position but not during
"start" (crank)
cycle. If
vehicle uses more than one accessory wire to power up heater & A/C controls, relays will be required.
J1-PIN#3- YELLOW: + 12VDC Starter Output
:Connect this
Yellow
wire to the solenoid side of the wire
which pr12 VDC when the ignition key is in the ignition
“Start”
position only.
J1-PIN#4- BLACK: NEG. (-) : CHASSIS GROUND Input
: Connect this BLACK
wire SECURELY TO A
CLEAN GROUND source.
J1-PIN#5- BLUE: +12 VDC True Ignition Output
:Connect
Blue
wire to the primary ignition wire supplying
+12 VDC when the ignition key is in the ignition
“On”
& "Start"
positions. Vehicles that have a 2nd ignition
wire, to supply power to 2nd ignition connect to J2-PIN# 2 Red/White.
J1-PIN#6- RED : + 12 VDC (fused) Main Power Source Input
: Connect
Red
wire to a main co12
VDC power source or to the positive terminal of the battery.
J2 : 14 PIN WIRE HARNESS
J2-PIN#1 WHITE POSITIVE +12 VDC PARKING LIGHT OUTPUT
Connect this
White
wire to positive side of the parking lights wire. This is a Relayed output
J2-PIN#2 RED/WHITE POSITIVE IGNITION #2 +12 VDC (6 Amp Max) for 2nd Ign. Wire
Connect this
Red/White
wire to the second Ignition wire that doesn’t draw more than 6 amps of current. If the
second ignition requires more than 6 amps, Connect an automotive relay as follows: Pin 85 to
Red/White
wire, pin 86 to Ground, Pin 87 to constant
Fused
12VDC and Pin 30 to the second ignition wire of vehicle.
J2-PIN#3 WHITE/VIOLET NEG EXT. TRIGGER (Auto / Hand Brake Input (Manual Trans.)
There are three uses for this wire:
(A)
As the 3
rd
trigger zone when alarm features are enabled
(B) As handbrake input for Manual Transmission vehicles (Mandatory)
(C) To initiate start up from an auxillary device such as a remote alarm, a Timer, or Temp. Sensor
J2-PIN#4 GRAY NEGATIVE CHANNEL #3 OUTPUT (Trunk Release or Other Option)
This
Gray
wire will provide a Negative 500 mA Output when the
#
“POUND
” button (III) is pressed for 1.0
second. It is programmable to activate even when ignition is “ON” or only when ignition is “OFF”.
J2-PIN#5 BLUE/WHITE NEGATIVE DISARM OUTPUT / DEFROST
This
Blue/White
wire is a programmable negative output:
BANK 2 FUNCTION 3
Option 1 : 0.5 sec. Neg. Disarm Pulse before remote starting & unlocking & trunk release
Option 2 : 1.0 sec. Neg. Disarm Pulse before remote starting & unlocking & trunk release
Option 3 : Defrost- Neg Pulse 4 sec after remote start
* Note when Option 1 or 2 is selected, system will provide Disarm pulse before confirmation parking light flash
and before unlocking or starting the vehicle. This does add 0.5 sec delay to the unlock function but is
necessary to disarm many 1999 & up factory security systems. e.g.. ‘99 Grand Prix GT.
