CS400 DIRECTSTART
REMOTE CAR S ALARM
CS400 VERSION 412
11
MANUAL TRANSMISSION VEHICLES
INSTALLATION & OPERATING INSTRUCTIONS
It is essential that ALL Safety connections are installed, tested and functioning properly for safe operation.
It is essential that ALL Safety connections are installed, tested and functioning properly for safe operation.
It is essential that ALL Safety connections are installed, tested and functioning properly for safe operation.
It is essential that ALL Safety connections are installed, tested and functioning properly for safe operation.
Installation of any remote start system into a manual transmission vehicle is entirely at your own risk. The
Installation of any remote start system into a manual transmission vehicle is entirely at your own risk. The
Installation of any remote start system into a manual transmission vehicle is entirely at your own risk. The
Installation of any remote start system into a manual transmission vehicle is entirely at your own risk. The
manufacturer assumes no risk or liability. Improper installation of a remote car starter may result in injury or death.
manufacturer assumes no risk or liability. Improper installation of a remote car starter may result in injury or death.
manufacturer assumes no risk or liability. Improper installation of a remote car starter may result in injury or death.
manufacturer assumes no risk or liability. Improper installation of a remote car starter may result in injury or death.
TO CONVERT UNIT TO MANUAL TRANSMISSION MODE
1.
Unscrew and remove the top portion of the main control module’s plastic casing.
2.
Locate and REMOVE JUMPER that is found directly on the circuit board beside the large microchip.
SAFETY CONNECTIONS FOR REMOTE CAR STARTER MODELS: CS100, CS300, CS400
J2-PIN#14 : HOOD PIN INPUT wire must be split and diode isolated to run a parallel negative (-) Door Input
and Hood Input. It is necessary that ALL DOORS be connected on this circuit.
J2-PIN#3 : External Trigger Input wire MUST BE CONNECTED to the wire which provides a negative (-) signal
when the hand brake is engaged.
Note: Removing the Black jumper cancels the External Trigger function and converts the input to a
hand brake input. DO NOT use this unit as a slave starter on manual transmission vehicles. DO NOT
install
on
convertibles
or
vehicles
in
which
entry
to
the
vehicle
cannot
be
monitored.
E.g.
convertibles, JEEPS, vehicles the doors can be removed etc
.
What Is “Remote Start Ready Mode”
When the remote starter is installed on a manual transmission vehicle a “Remote Start Ready Mode” safety
procedure must be followed EACH time the vehicle is exited. The safety procedure is in place to remind the user
to leave the vehicle in NEUTRAL and NOT in gear before remote starting. If the safety procedure is not completed,
the vehicle WILL NOT remote start but all other options will function normally. The remote start system monitors
the doors and handbrake at all times. It is essential that all doors and handbrake connections are functioning
properly to ensure safe operation. This is the responsibility of the installer!
*Installers must make sure all the entry points are monitored via the doorpin connection.
** Users must also make sure that all safety connections are operational and should also periodically test to
ensure that all entry point connections are in fact functioning correctly.
OPERATING INSTRUCTIONS: Entering “Ready Mode”
OPERATING INSTRUCTIONS: Entering “Ready Mode”
OPERATING INSTRUCTIONS: Entering “Ready Mode”
OPERATING INSTRUCTIONS: Entering “Ready Mode”
1) Make sure ALL doors and hood are shut and vehicle is running by the ignition key.
2) Place vehicle in Neutral and set Parking Brake.
3) Press START Button #2 (*) for 2 seconds. Parking lights will flash then come back ON.
(You should hear Parking light relay “click” twice)
* If a RED LED is installed, the LED light will begin flashing to confirm “Manual Transmission Ready Mode” is enabled.
4) Turn key to OFF position and remove key. Vehicle engine should remain running.
5)
Open door and Exit vehicle. Close the door then press the START Button #2 (*) to shut off engine.
(Parking lights will confirm with 2 slow flashes)
6) System is now in “READY MODE” and will allow vehicle to be remote started by pressing the START
Button # 2 (*) for 2 seconds.
7) To remote start vehicle press the START Button for 2 seconds and release. System will flash Park lights
once to confirm signal received then attempt to start engine. Engine start is confirmed when Parking lights
come back ON. As long as engine is running under remote start Park lights will remain ON.
8) NOTE: Any time the vehicle is re-entered (door is opened) the remote starter will EXIT ready mode. If
“Ready Mode” has not enabled parking lights will flash 4 times if a remote start attempt is made.
