background image

Instruction Sheet 

1 of 8 

© 2022 TE Connectivity Ltd. family of companies. 
All Rights Reserved. 
  

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.  Other logos, product, and/or company names may be trademarks of their respective owners. 

PRODUCT INFORMATION 1-800-522-6752 

This controlled document is subject to change. 
For latest revision and Regional Customer Service, 
visit our website a

www.te.com

408-35292 

17 JUN 2022  Rev A

PROPER USE GUIDELINES

 

Cumulative trauma disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional 
use and low-volume applications. A wide selection of powered application equipment is available for extended-use production operations. 
The SDE-SA hand tool is a commercial-grade tool. Product crimped with this tool meets the wire barrel crimp height requirement for hand 
tools in the appropriate 114 application specification, but might not comply with other feature parameters of the specification. 

Figure 1: SDE-SA Commercial Hand Tool Assembly 2390075-1 with Die Assembly 2390075-2 

 

Insulation crimper (upper die) 

Moving jaw 

11 

Handle 

Wire crimper (upper die) 

Stationary jaw 

12 

Die-retaining screws (2) 

Die set 2390075-2 

Nut 

13 

Die-retaining pins (4) 

Wire anvil (lower die) 

Locator 

14 

Ratchet adjustment wheel 

Insulation anvil (lower die) 

10 

Emergency ratchet release 

 

 

 

 

 

SDE-SA Commercial Hand Tool Assembly 

PN 2390075-1 with 

Die Assembly PN 2390075-2 

Содержание 2390075-1









Отзывы: