![background image](http://html.mh-extra.com/html/sealey/auto-service-line-sx0407/auto-service-line-sx0407_instructions_1227057001.webp)
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS for:
Glow Plug Removal Set
MODEL No:
SX0407
WARNING!
Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
DO NOT
use tools if damaged.
Maintain tools in good and clean condition for best and safest performance.
Ensure that a vehicle which has been jacked up is adequately supported with axle stands.
Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.
Wear suitable clothing to avoid snagging.
DO NOT
wear jewellery and tie back long hair.
Account for all tools and parts being used and do not leave them in or near the engine.
DO NOT
attempt to start engine or move vehicle, whilst tools are fitted and work is in progress.
Ensure any disconnected fuel pipes are plugged to avoid spillage.
Account for all tools and parts being used,
DO NOT
leave them in or near the engine. Return all parts to the case and store this in a
safe, dry, childproof location.
IMPORTANT:
These instructions are provided as a guide only. Always refer to the vehicle manufacturer’s service instructions,
or a proprietary manual, to establish the current procedure and data.
WARNING!
The warnings referred to in this guide cannot cover all possible conditions and situations that may occur. It must be understood
that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
1.
SX0407.01
De-carbonising Wire Brush (8mm)
2.
SX0407.02
De-carbonising Wire Brush (5mm)
3.
SX0407.03
Glow Plug Top Remover, 2.5mm
4.
SX0407.04
Glow Plug Top Remover, 3.5mm
5.
SX0407.05
Glow Plug Top Remover, 4.0mm
6.
SX0407.06
Tap, M5.5 x 9mm
7.
SX0407.07
Tap, M8 x 10mm
8.
SX0407.08
Pilot Drill, 4.5mm
9.
SX0407.09
Pilot Drill, 2.6mm
10.
SX0407.10
T-Bar
11.
SX0407.11
Pilot Drill Centring Sleeve (x2)
12.
SX0407.12
Bit - Glow Plug Top Nut Remover &
Drill Holding Adaptor (also for items 8 & 9)
13.
SX0407.13
Glow Plug Removal Thread Rod (x2)
14.
SX0407.14
Removal Nut
15.
SX0407.15
Tap Holding Adaptor (for items 6 & 7)
16.
SX0407.16
Centring Adaptor
17.
SX0407.17
Glow Plug Removal Sleeve
Designed for removal of damaged/broken glow plugs from cylinder heads. Suitable for glow plugs with a M8 x 1.0 thread. Set includes all required
adaptors, centring and cleaning tools to safely remove the glow plug without damaging the engine.
2. INTRODUCTION
1. SAFETY INSTRUCTIONS
SX0407 Issue No: 1 - 07/12/10
Original Language Version