instructions for
vices
model no:
Asv100, Asv125, Asv150, Asv200, Asv250 &
Asv300.
Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. sAfeTy
1.1.
GeneRAl sAfeTy
WARninG!
this is a heavy item, care must be taken when lifting or moving it.
WARninG!
Ensure the vice is properly fastened to the work surface.
8
do noT
hammer any part of this vice except the anvil.
8
do noT
operate the vice if any parts are missing as this may cause failure and/or
personal injury.
8
do noT
use the vice for a task it is not designed to perform.
8
do noT
operate the vice when you are tired, under the influence of alcohol, drugs
or intoxicating medication.
8
do noT
allow children to operate the vice.
9
When sawing, cutting or drilling in connection with this vice always use appropriate
industrial gloves and eye protection.
9
take care not to get your fingers trapped between the jaws of the vice at any time.
9
replace or repair damaged parts. use an authorised service agent and recommended
parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery
and contain long hair.
9
use in a suitable work area. Keep area clean, tidy and free from unrelated materials.
9
Ensure there is adequate lighting.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
2. inTRoducTion
A range of bench mounting steel vices suitable for workshop, garage and machine-shop use. fixed bases direct-mount onto work bench and a
swivel vice plate adaptor is available as an optional extra. (not available for models AsV250 and AsV300) All models in this range include an anvil.
3. specificATion
Model no
Jaw size
Jaw opening optional swivel Adaptor Plate
AsV100
100mm
100mm VsB4
AsV125
125mm
125mm VsB5
AsV150
150mm
150mm VsB6
AsV200
200mm
200mm VsB8
AsV250
250mm
250mm n/A
AsV300
300mm
300mm n/A
4. Assembly
4.1.
Without optional swivel vice plate adaptor.
4.1.1.
the vice is fully assembled and should be correctly secured to the work surface before use.
4.2.
With optional swivel vice plate adaptor.
note:
numbers in brackets refer to item numbers shown in the Parts List.
4.2.1.
screw the two bolts (6) into the base plate (8).
4.2.2.
Locate the base plate inside the swivel base (7) pass the bolts through the locating holes in the back jaw (5), locate the washer (3) onto
the bolt and secure using the locking nut (2).
4.2.3.
secure the swivel base to the work surface before use.
4.2.4.
the vice can be rotated by loosening the locking nuts and rotating the vice.
WARninG!
Ensure the locking nuts are fully tightened before using the vice.
AsV100, 125, 150, 200, 250, 300 (H3f) issue 4 14/12/17
Original Language Version
© Jack sealey Limited
refer to
instructions
fig.1
