background image

1

T

o

ta

l H

eig

h

t

G

ro

u

nd H

eig

h

t

H

eadr

o

o

m

Drive Through Height

Drive Through Width

Over Guide Width

Note: Due to ongoing development some of the information and procedures may not exactly correlate to the product received. If in 

doubt, please ask your supplier.

Electric Roller Garage Door 

Installation Instructions

ALWAYS CHECK

 ON DELIVERY THAT THE ORDER DETAILS ARE CORRECT AND THE 

DOOR IS UNDAMAGED 

BEFORE REMOVING ANY EXISTING DOORS

.

Check:
i) delivery 

note

ii) order 

sheet

iii)  door dimensions/colour
iv)  opening dimensions \clearances
v)   components
vi)  Check for any damage to the guide rails 

or the outside roll of the curtain

Do not proceed further with the 
installation unless you are sure that 
the door is the correct size, and all 
components are present.

Widths

Order Width = Over Guide Width 

Drive Through Width

 = Over Guide Width less 150mm for 75mm guides

Drive Through Width = Over Guide Width less 180mm for 90mm guides

Curtain Width = 

Over Guide Width less 90mm

Axle Width = 

Over Guide Width less 90mm (without spring)

                  

Over Guide Width less 73mm (with spring)

Heights

Order Height = Guide Height

Total Height 

= Guide End Plate

Headroom/End Plate 

 

up to 2.5m Guide Height = 300mm 
up to 3.5m Guide Height = 350mm

Drive Through Height

 = Guide Height less 55mm

1

April 2013 

Issue 1 MK516BO

Sequence of Installation & Contents

1. 

Pre-installation and component check

2. 

Installation options and criteria for compliance with LPS 1175

3. Prepare 

the 

opening

4. Prepare 

the 

guide 

rails

5.  

Fit end plates, guides & axle (& optional fascia)

6. Fit 

emergency 

overrides

7. 

Curtain adjustment (reducing height/making repairs)

8. 

Install the curtain in the guides, attach to axle & fit stops

9. 

Curtain locking & setting motor limit switches

10. 

Commissioning

11. 

Maintenance, repairing and dismantling instructions

1.  PRE-INSTALLATION AND COMPONENT CHECK:

www.samsondoors.co.uk

0800 328 6250

www.samsondoors.co.uk

www.samsondoors.co.uk

0800 328 6250

www.samsondoors.co.uk

Summary of Contents for SeceuroGlide Manual













Reviews: