background image

TO WATCH VIDEOS GO TO: 

tinyurl.com/lgh5x3h

TO WATCH VIDEOS GO TO: 

tinyurl.com/lgh5x3h

Contents

Preparation ......................................2-5
Assembly .......................................6-10
Installation ..................................11-28

Install the Door Control ............21-22
Install the Protector System ......23-26

 Connect 

Power 

.........................27-28

Adjustments .................................29-31
myQ® Smartphone Control .................32
Operation .....................................33-36
 Features 

.......................................34

Using your Garage Door Opener .....35
Push Button Door Control ..............35
 Remote Control and

Keyless Entry ................................35

 Homelink® 

...................................35

To Erase the Memory .....................36
To Open the Door Manually ...........36

Maintenance .....................................37
Troubleshooting ...........................38-39
Accessories ........................................40
Warranty ...........................................41
Repair Parts .................................42-43

Owner’s Manual

C253

Chain Drive 

Garage Door Opener

FOR RESIDENTIAL USE ONLY

PRE-PROGRAMMED REMOTE CONTROL 

INCLUDED

www.chamberlain.com

www.mychamberlain.com

•  Please read this manual and the enclosed safety materials carefully!
•  Fasten the manual near the garage door after installation.
•  The door WILL NOT CLOSE unless the Protector System® is connected 

and properly aligned.

• Periodic checks of the garage door opener are required to ensure

safe operation.

•  The model number label is located on the front panel of your garage 

door opener.

• This garage door opener is compatible with myQ® and

S

b

2.0® accessories.

• DO NOT install on a one-piece door if using devices or features

providing unattended close. Unattended devices and features are

to be used ONLY with sectional doors.

Garage Opener

Summary of Contents for C253

























































































Reviews: