background image

7SG13 Delta P20064 FM1 Autoreclosing 

The copyright and other intellectual property rights in this document, and in any model or article produced from it 
(and including any registered or unregistered design rights) are the property of Siemens Protection Devices Ltd. 
No part of this document shall be reproduced or modified or stored in another form, in any data retrieval system, 
without the permission Siemens Protection Devices Ltd., nor shall any model or article be reproduced from this 
document unless Siemens Protection Devices Ltd. consent.  
 
While the information and guidance given in this document is believed to be correct, no liability shall be accepted 
for any loss or damage caused by any error or omission, whether such error or omission is the result of 
negligence or any other cause. Any and all such liability is disclaimed. 
 
©2010 Siemens Protection Devices Ltd. 

 
7SG13 Delta 

Protection and Control Relays 

 

 

Document Release History 

This document is issue 2010/02. The list of revisions up to and including this issue is: 

Pre release 

 

2010/02 

Document reformat due to rebrand 

2004/08 First 

issue 

 

 

 

Software Revision History 

 

 

 

 

 

 
 
 

Summary of Contents for 7SG13 Delta








Reviews: