background image

CONGRATULATIONS!

You’ve purchased the finest in natural lighting technology with your new OttLite

®

 

product.

PRODUCT REGISTRATION FORM

Please complete the enclosed Product Registration Form and return it today by 
mail or register online by going to: OttLite.com/warranty.

WARNING:

 To prevent electric shock, make sure the lamp is not plugged in until 

all steps are complete.

NOTE: THIS UNIT IS FULLY ASSEMBLED

1. 

Remove the lamp from the packaging and place on a flat surface.

2. 

Connect power adapter input (A) into connector (B) in the rear-bottom of the lamp.

3. 

Plug the power adapter (C) into a standard household 120V AC outlet. 

Note: 

Only use with the supplied power adapter to avoid damage or fire.

  

4. 

Power switch (D) is a “touch” switch that controls 

ON/OFF

 power, the LED 

brightness settings and the mode functions of the lamp.

5. 

To turn the lamp 

ON

, touch (D) once. To adjust brightness, touch (D) again. The 

lamp has 3 brightness settings and then the fourth touch will turn the light 

OFF

.

6. 

Touch and hold (D) to change light modes. The three modes are; ClearSun LED, 
Sanitizing, and Cl Sanitizing. Cl Sanitizing mode utilizes both 
the Clearsun LEDs and Sanitizing LEDs simultaneously to provide continuous 
cleaning while using the lamp.  

NOTE:

 The active mode will be indicated by the lights next to the icons. If 

indicator light (E) is illuminated, ClearSun mode is on. If indicator light (F) 
is illuminated, Sanitizing mode is on. If both indicator lights (E and F) are 
illuminated, Cl Sanitize mode is on. 

7. 

To position the shade simply bend the flex-neck as needed to point the light. 
Please hold the lamp base while adjusting the lamp.

WIRELESS CHARGING INSTRUCTIONS:

Wireless charging requires a Qi-certified device. To determine if your device is  
Qi-certified, please visit the Wireless Power Consortium website.

To wirelessly charge a device, perform the following:
•  Place the device, which supports Qi wireless charging standard, face up on the 

middle of the Qi wireless charging emblem (K). 

•  A red indicator light (L) will come on to indicate charging.
•  Check the charge level on your device periodically to determine when device is 

fully charged. 

NOTE:

 Lamp DOES NOT provide any indication of when device is 

fully charged. 

CAUTION!

  

DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL 

AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE. 

USB CHARGING PORT

THIS LAMP CONTAINS a 5V, 2,1A USB output port (G) located on the bottom rear 
of lamp. USB port can charge items such as tablets, cellular phones, etc.

SAFETY WARNING:

  

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, 

OR INJURY TO PERSONS

1. 

Turn lamp off and

 WAIT UNTIL LAMP HEAD (H) IS COOL

 

before handling.

2. 

The LED panel (J) might get hot after several hours of continuous use 

DO NOT

 

place your hands directly on LED light panel.

3. 

Never use with an extension cord unless the plug can be fully inserted into the 
receptacles in the extension cord.

4. 

Do not alter the plug.

5. 

The lamp head included with this unit cannot be replaced by the consumer.

6. 

INDOOR USE ONLY.

NOTE:

 The important safety instructions appearing in this instruction sheet are not 

meant to cover all possible conditions and situations that may occur.  It must be 
understood that common sense, caution, and care must be used with any electrical 
product.

CAUTION!

  

IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS 

DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE 

AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.

CAUTION!

  

THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN 

THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.

FCC PART 15 

Note: This equipment has been tested and found to comply with the limits for a Class 
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if 
not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that the 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined 
by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:

•  

Reorient or relocate the receiving antenna.

•  

Increase the separation between the equipment and receiver.

•  

Connect the equipment into an outlet on a circuit different from that to which  

    the receiver is connected.

•  

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions:
    (1) this device may not cause harmful interference, and 
    (2) this device must accept any interference received, including interference that  
         may cause undesired operation.

FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION: 

To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 
20cm from nearby persons.

IC CANADA

This device contains licence-exempt transmitter(s)/receiver that comply with 
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). 
Operation is subject to the following two conditions: 
1. This device may not cause interference. 
2. This device must accept any interference, including interference that may cause  
    undesired operation of the device.

CAN RSS-216/CNR-216
CAN ICES-005 (B)/NMB-005 (B)

CAUTION:

 Any change or modification to product not expressly recognized by 

OttLite Technologies voids OttLite’s responsibility for proper function of product.

POWER ADAPTER SPECIFICATION:

Input: AC 100-240V, 50/60 Hz, 1A Max
Output: 12V DC, 2.5A with a Male DC Plug

Qi CHARGER SPECIFICATION: 

Output: up to 5 Watts depending on device

The “Qi” symbol is a trademark of the Wireless Power Consortium

  

 

ENGLISH

 

Achieve LED Sanitizing Lamp with Wireless Charging

A

C

Achieve LED Sanitizing Lamp with Wireless Charging

SCDQCWGS-WA     

 

 K8SC

INS210652     

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

           

 

 

 

 

 

 

 

 

                             REV052621

B

D

H

G

E

F

(ClearSun mode)
(Mode ClearSun)

(Modo ClearSun)

(Sanitizing mode)

(Mode Assainissement)

(Modo de desinfección)

J

K

L

L

Reviews: