FOCUS
120v-277v
120v-277v
120v-277v
FOCUS
120v-277v
120v-277v
120v-277v
FOCUS
120v-277v
120v-277v
120v-277v
FOCUS
120v-277v
120v-277v
120v-277v
FFL-24-T5HO-HE
FFL-39-T5HO-HE
FFL-54-T5HO-HE
FFL-17-T8-HE
FFL-25-T8-HE
FFL-32-T8-HE
FFL-24-T5HO-HE
FFL-39-T5HO-HE
FFL-54-T5HO-HE
FFL-17-T8-HE
FFL-25-T8-HE
FFL-32-T8-HE
FFL-24-T5HO
FFL-39-T5HO
FFL-54-T5HO
FFL-17-T8
FFL-25-T8
FFL-32-T8
FFL-24-T5HO
FFL-39-T5HO
FFL-54-T5HO
FFL-17-T8
FFL-25-T8
FFL-32-T8
RECOMMENDED
FOCUS FA-26
Mounting Pedestal
RECOMMENDED
FOCUS FA-26
Mounting Pedestal
1.
Make sure electrical supply power is shut off at circuit breaker before
starting fixture installation or servicing of fixture.
2.
Using thread sealant, thread fixture onto junction box or other mounting
device (not supplied) until it is at desired direction. Tighten provided lock
nut to ensure that the fixture is firmly locked into adjusted position.
3.
Attach fixture leads to line in leads observing polarity (black to black,
white to white and green to ground) using approved silicone-filled safety
wire connectors.
4.
Attach junction box cover plate to junction box (not supplied). Make sure
that wires are not pinched between junction box cover and junction box.
1.
Make sure electrical supply power is shut off at circuit breaker before
starting fixture installation or servicing of fixture.
2.
Using thread sealant, thread fixture onto junction box or other mounting
device (not supplied) until it is at desired direction. Tighten provided lock
nut to ensure that the fixture is firmly locked into adjusted position.
3.
Attach fixture leads to line in leads observing polarity (black to black,
white to white and green to ground) using approved silicone-filled safety
wire connectors.
4.
Attach junction box cover plate to junction box (not supplied). Make sure
that wires are not pinched between junction box cover and junction box.
5.
Coat exposed fixture threads with thread sealant to prevent moisture from
entering junction box or other mounting device.
6.
Install lamp; refer to section below.
7.
To adjust fixture aiming angle, loosen swivel screw. Do not remove
completely. Hold fixture at selected angle and tighten swivel screw firmly
with #2 Phillips screw driver.
8.
Turn power on to the fixture and check for proper operation.
5.
Coat exposed fixture threads with thread sealant to prevent moisture from
entering junction box or other mounting device.
6.
Install lamp; refer to section below.
7.
To adjust fixture aiming angle, loosen swivel screw. Do not remove
completely. Hold fixture at selected angle and tighten swivel screw firmly
with #2 Phillips screw driver.
8.
Turn power on to the fixture and check for proper operation.
LAMP INSTALLATION/REPLACEMENT:
CAUTION: Do not exceed maximum wattage marked on fixture label.
1.
To prevent electrical shock, turn off electrical power supply before
servicing.
2.
Remove 2 side plate screws, loosen third screw and pivot side plate.
LAMP INSTALLATION/REPLACEMENT:
CAUTION: Do not exceed maximum wattage marked on fixture label.
1.
To prevent electrical shock, turn off electrical power supply before
servicing.
2.
Remove 2 side plate screws, loosen third screw and pivot side plate.
3.
Slide lens outward to expose lamp.
4.
Replace with correct wattage type of lamp, marked on fixture label.
5.
Re-install front lens & side plate screws.
3.
Slide lens outward to expose lamp.
4.
Replace with correct wattage type of lamp, marked on fixture label.
5.
Re-install front lens & side plate screws.
NOTE: Must be installed by a licensed electrician per local codes.
For Questions Call 1-888-882-1350
NOTE: Must be installed by a licensed electrician per local codes.
For Questions Call 1-888-882-1350
INSTALLATION INSTRUCTIONS FOR
120 - 277 VOLT T5HO & T8 FLUORESCENT FLOOD LIGHTS
INSTALLATION INSTRUCTIONS FOR
120 - 277 VOLT T5HO & T8 FLUORESCENT FLOOD LIGHTS
INSPECTED BY:
INSPECTED BY:
STANDARD J-BOX
(SUPPLIED BY OTHERS)
STANDARD J-BOX
(SUPPLIED BY OTHERS)
120v Install FFL T5HO/T8
120v Install FFL T5HO/T8
010813
010813
