ZyXEL Communications XS1930-10 Page 262 User Manual Download | Manualshive

Page: 262 / 381

background image

XS1930 Series User’s Guide

262

C

HAPTER

33

DHCP

33.1 DHCP Overview

This chapter shows you how to configure the DHCP feature.

DHCP (Dynamic Host Configuration Protocol RFC 2131 and RFC 2132) allows individual computers to
obtain TCP/IP configuration at start-up from a server. If you configure the Switch as a DHCP relay agent,
then the Switch forwards DHCP requests to DHCP server on your network. If you don’t configure the
Switch as a DHCP relay agent then you must have a DHCP server in the broadcast domain of the client
computers or else the client computers must be configured manually.

33.1.1 What You Can Do

• Use the

DHCPv4 Status

screen (

Section 33.3 on page 263

) to display the relay mode.

• Use the

DHCPv4 Relay

screen (

Section 33.4 on page 264

) to enable and configure global DHCPv4

relay.

• Use the

VLAN Setting

screen (

Section 33.4.6 on page 269

) to configure your DHCPv4 settings based on

the VLAN domain of the DHCPv4 clients.

• Use the

DHCPv6 Relay

screen (

Section 33.5 on page 273

) to enable and configure DHCPv6 relay.

33.1.2 What You Need to Know

Read on for concepts on DHCP that can help you configure the screens in this chapter.

DHCP Modes

If there is already a DHCP server on your network, then you can configure the Switch as a DHCP relay
agent. When the Switch receives a request from a computer on your network, it contacts the DHCP
server for the necessary IP information, and then relays the assigned information back to the computer.

DHCPv4 Configuration Options

The DHCPv4 configuration on the Switch is divided into

Global

and

VLAN

screens. The screen you should

use for configuration depends on the DHCP services you want to offer the DHCP clients on your network.
Choose the configuration screen based on the following criteria:

•

Global

- The Switch forwards all DHCP requests to the same DHCP server.

•

VLAN

- The Switch is configured on a VLAN by VLAN basis. The Switch can be configured to relay

DHCP requests to different DHCP servers for clients in different VLAN.

«
...
260
261
262
263
264
...
»

Summary of Contents for XS1930-10






























































































































































































































































































































































































Reviews:

No comments

Related manuals for XS1930-10

Brand: Paradyne Pages: 86

Express Ethernetwork DI-704P

Brand: D-Link Pages: 2

Brand: D-Link Pages: 267

AirPlus DWL-810

Brand: D-Link Pages: 25

Brand: D-Link Pages: 32

Brand: D-Link Pages: 6

Brand: D-Link Pages: 221

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 68

Express Ethernetwork DI-707P

Brand: D-Link Pages: 14

Wireless Router

Brand: Watchguard Pages: 11

Brand: D-Link Pages: 32

Brand: D-Link Pages: 28

Brand: D-Link Pages: 48

Brand: D-Link Pages: 83

Brand: D-Link Pages: 155

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

5big - Network NAS Server

Brand: LaCie Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands