manualshive.com logo in svg

ZyXEL Communications ADSL 2+ Security Gateway, User Manual, Page: 135 / 686

Share
Download
ZyXEL Communications ADSL 2+ Security Gateway User Manual Download Page 135

 Chapter 6 LAN Screens

ZyWALL 2 Plus User’s Guide

135

6.3  DHCP 

The ZyWALL can use DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 
2132) to automatically assign IP addresses subnet masks, gateways, and some network 
information like the IP addresses of DNS servers to the computers on your LAN. You can 
alternatively have the ZyWALL relay DHCP information from another DHCP server. If you 
disable the ZyWALL’s DHCP service, you must have another DHCP server on your LAN, or 
else the computers must be manually configured. 

6.3.1  IP Pool Setup

The ZyWALL is pre-configured with a pool of IP addresses for the computers on your LAN. 
See 

Chapter 46 on page 613

 for the default IP pool range. Do not assign your LAN computers 

static IP addresses that are in the DHCP pool.

6.4  RIP Setup

RIP (Routing Information Protocol, RFC 1058 and RFC 1389) allows a router to exchange 
routing information with other routers. 

RIP Direction

 controls the sending and receiving of 

RIP packets. When set to 

Both

 or 

Out Only

, the ZyWALL will broadcast its routing table 

periodically. When set to 

Both

 or 

In Only

, it will incorporate the RIP information that it 

receives; when set to 

None

, it will not send any RIP packets and will ignore any RIP packets 

received.  

RIP Version

 controls the format and the broadcasting method of the RIP packets that the 

ZyWALL sends (it recognizes both formats when receiving). 

RIP-1

 is universally supported; 

but 

RIP-2

 carries more information. RIP-1 is probably adequate for most networks, unless you 

have an unusual network topology.
Both 

RIP-2B

 and 

RIP-2M

 send routing data in RIP-2 format; the difference being that 

RIP-

2B

 uses subnet broadcasting while 

RIP-2M

 uses multicasting. Multicasting can reduce the 

load on non-router machines since they generally do not listen to the RIP multicast address 
and so will not receive the RIP packets. However, if one router uses multicasting, then all 
routers on your network must use multicasting, also.
By default, 

RIP Direction

 is set to 

Both

 and 

RIP Version

 to 

RIP-1

.

6.5  Multicast

Traditionally, IP packets are transmitted in one of either two ways - Unicast (1 sender - 1 
recipient) or Broadcast (1 sender - everybody on the network). Multicast delivers IP packets to 
a group of hosts on the network - not everybody and not just 1. 
IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to establish 
membership in a Multicast group - it is not used to carry user data. IGMP version 2 (RFC 
2236) is an improvement over version 1 (RFC 1112) but IGMP version 1 is still in wide use. If 
you would like to read more detailed information about interoperability between IGMP 
version 2 and version 1, please see sections 4 and 5 of RFC 2236. The class D IP address is 
used to identify host groups and can be in the range 224.0.0.0 to 239.255.255.255. The address 

Summary of Contents for ADSL 2+ Security Gateway















































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments