Zooper Premier EX+ Operation And Installation Manual Download Page 14

Page: 14 / 17

PREMIER EX PLUS – OPERATION & INSTALLATION MANUAL

PAGE 14

DOCUMENT: GLT-MAN.115

ISSUE: 1 DATE: 22/8/05
AUTHOR: NRPJ

ELECTRICAL SPECIFICATIONS

Mains Voltage

230 Vac. 59/60Hz +15%, -10%.

Charger Voltage

25 – 30 Vdc (set internally to 27.6V)

Battery Voltage

24V SLA (2 x 12V)

Battery Space

7.0 AH maximum

Mains Supply Protection

3.15 AF HRC 20 x5mm fuse

Charger Voltage Protection

1.6 AT 20 x 5mm glass fuse

Battery Supply Protection

3.15 AT 20 x 5mm glass fuse

Reverse battery protection

Battery fuse

Sounder Output (1

and 2

stage)

24 Vdc nominal

Sounder Output protection

400mAF 20 x 5 mm glass fuse

Sounder EOL

10K

Max sounder circuit resistance

25 R

Auxiliary Supply Output

24 Vdc nominal

Auxiliary Supply protection

1 AT 20 x 5 mm glass fuse

Auxiliary Relay contacts (1

and 2

stage)

30Vac / dc 1.0 A each

Bottle Output

24 Vdc nominal

Bottle Output protection

1.0AT 20 x 5 mm glass fuse

Bottle end of line

10K

Zone Voltage

20 Vdc nominal

Quiescent Zone current

8 mA per circuit

Zone end of line

2K7

Max Zone circuit resistance

100 R

Max resistance other circuits

100 R

Quiescent battery current (tone muted)

72 mA nominal

Quiescent bat current (tone not muted)

85 mA nominal

Max total load current (Snd 1 & 2 , Bottle)

1.6 A ( although each may be to fuse rating )

Circuits monitored for O/C and S/C

Bottle output,
1

and 2

stage snd outputs,

Zones 1 and 2.

Circuits monitored for O/C only

Hold/Abort
Auto/Manual,
Gas fired,
Manual release.
(S/C gives active condition although a resistance of up to
500 R will still give an active condition)

FUSE RATINGS

Mains Fuse

3.15 A HBC

Charger Fuse

1.6A T

Battery Fuse

3.15A T

First Stage Sounder Fuse

400 mA F

Second Stage Sounder Fuse

400 mA F

Bottle Fuse

1A T

Aux 28V Fuse

1A T

Summary of Contents for Premier EX+


















Search results

Summary of Contents for Premier EX+

Reviews:

Related manuals for Premier EX+

Brands by name

Popular brands

Zooper Premier EX+, Operation And Installation Manual

Search results

Summary of Contents for Premier EX+

Reviews:

Related manuals for Premier EX+

Brands by name

Popular brands