Zontes ZT125-Z2 Service Manual Download Page 48

Page: 48 / 76

7-FRONT FORK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251100-102000 Non-standard bolt M6×16

（

304 stainless steel

）

1274100-057095 Flanging bushing φ6.2×φ8.5×3.5

＋

φ14×1.5

1244100-052000 Buffer rubber of flanging bushing

（

φ8.5×φ14×1

）

4041201-152051 KD150

－

Z2 dark gray head cover left part

4041201-153051 KD150

－

Z2 dark gray head cover right part

4041201-224000 ZT155-Z2 windshield

1251300-063093 Plywood M6×11×15

（

color zinc

）

1170300-099000 SK150-Z headlights

1240300-066000 KD250-J head cover pad

PROCEDURE:

●

Left and right head cover

Remove the 6 bolts

⑴

with a 4# inner hexagon, take out the bushing

⑵

, cushion rubber

⑶

, and remove the left

head cover

⑷

and right head cover

⑸

●

Windshield

Use 4# inner hexagon to remove 3 bolts (1), take out bushing (2), cushion rubber (3), and take off windshield

(5). (The rubber pad

⑼

on the upper part of the headlight rear shell needs to be cut into two parts and pasted on

the upper part of the headlight rear shell respectively.)

CAUTION:

●

The head unit should be supported during the disassembly process and protective measures should be taken

toprevent scratching the lamp cover or paint surface.

Fig.11 FRONT FORK

COMPONENT

Head and headlights component 2

Summary of Contents for ZT125-Z2













































































Search results

Summary of Contents for ZT125-Z2

Reviews:

Related manuals for ZT125-Z2

Brands by name

Popular brands

Zontes ZT125-Z2, Service Manual

Search results

Summary of Contents for ZT125-Z2

Reviews:

Related manuals for ZT125-Z2

Brands by name

Popular brands