Zontes ZT125-Z2 Service Manual Download Page 63

Page: 63 / 76

8-FUEL TANK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1240300-066000 KD250-J head cover pad

1181200-101000 KD150

－

G1 lock set

1240300-021000 HJ125

－

6 pod glass strip (1.5m)

0.33

500mm

ZT155-Z2 fuel tank

1250105-137093 GB5789M6×16

（

color zinc

）

1050954-031000 T02 built-in fuel pump - ZT310T

Fig.5 FUEL TANK

COMPONENT

Fuel tank component

PROCEDURE:

●

Fuel tank sub-assembly

Remove the rubber strip

⑷

from the fuel tank

⑶、

head cover pad

⑴

Use the key to remove the fuel tank cover lock (3).

（

The direction indicated by the arrow is the front of the bike.

Do not install the fuel tank lock backwards, otherwise the fuel tank will be damaged.

）

Turn the fuel tank over, remove the dump valve

①

at the bottom in the direction of the arrow, and then remove

the fuel pipe

②

connecting the fuel tank.The check valve

③

is not connected to any part of the fuel tank.

CAUTION:

●

The parts should be protected during the disassembly process to prevent damage to the paint surface.

Summary of Contents for ZT125-Z2













































































Search results

Summary of Contents for ZT125-Z2

Reviews:

Related manuals for ZT125-Z2

Brands by name

Popular brands

Zontes ZT125-Z2, Service Manual

Search results

Summary of Contents for ZT125-Z2

Reviews:

Related manuals for ZT125-Z2

Brands by name

Popular brands