Zontes ZT125-Z2 Service Manual Download Page 69

Page: 69 / 76

11-REAR COVER COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251100-102000 Non-standard bolt M6×16

（

304 stainless steel

）

1274100-057095 Flanging bushing φ6.2×φ8.5×3.5

＋

φ14×1.5

1244100-052000 Buffer rubber of flanging bushing

（

φ8.5×φ14×1

）

1251300-063093 Plywood M6×11×15

（

color zinc

）

1171200-062000 KD150

－

Z2 tail light

PROCEDURE:

●

Taillight assembly

Use 4# inner hexagon to remove 2 bolts

⑴

, take off the bushing

⑵

, cushion rubber

⑶

Locate and unplug the tail light connector at the position indicated by the arrow, remove the tail light

⑸

in the

direction of the arrow, and remove the splint

⑷

on the tail light.

CAUTION:

●

The side cover, seat cushion, rear armrest and other components need to be removed in advance.

●

The material should be protected during discomponent to prevent scratching the lamp.

Fig.3 REAR COVER

COMPONENT

Taillight component

Summary of Contents for ZT125-Z2













































































Search results

Summary of Contents for ZT125-Z2

Reviews:

Related manuals for ZT125-Z2

Brands by name

Popular brands

Zontes ZT125-Z2, Service Manual

Search results

Summary of Contents for ZT125-Z2

Reviews:

Related manuals for ZT125-Z2

Brands by name

Popular brands