Zontes ZT125-Z2 Service Manual Download Page 14

Page: 14 / 76

2-FRAME & ENGINE COMBINATION

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1244100-061000 ZT250 anti-water rubber of frame

1251100-142000 Non-standard hexagon socket bolt M10 × 1.5 × 130

1244100-089000 ZT250-R guard bar anti-drop glue

1250305-002091 GB6187.1 M8

（

White zinc

）

65±5N.m

1250105-042091 GB5789M8 × 75 (level 10.9 / white zinc)

1251300-057093 Non-standard nuts M10×1.5 (color zinc)

65±5N.m

1251100-085093 Non-standard bolt M10×1.5×75 (color zinc)

4111200-006051 KD150

－

Z2 right crash bar (dark gray matte)

1221200-089000 KD150

－

Z2 right side of water tank cover

1244100-002000 ZT250

－

S Side cover round rubber

4111200-004051 KD150

－

Z2 left crash bar (dark gray matte)

1221200-088000 KD150

－

Z2 left side of water tank cover

Fig.1 FRAME & ENGINE

COMBINATION

Frame & engine combination 1

CAUTION

：

●

Use the appropriate tools to support the whole vehicle to prevent accidents caused by the dumping of

the vehicle during the disassembly process; single operation is strictly prohibited.

●

All standard parts must meet the standard torque value during reassembly.

PROCEDURE:

●

Guard bar component

First remove the lower fairing assembly.
Take off rubber

⑴

Grasp the right crash bar assembly firmly, and use 8# inner hexagon to remove the hexagon socket bolt

⑵

;

remove the protecting rubber

⑶

and install the shaft sleeve

⑷

Refer to the above steps to remove the anti-drop glue

⑶

and install the shaft sleeve

⑷

on the left.

One person fixes the 2 bolts

⑻

at the bracket with a 14# sleeve first, and the other uses a 14# sleeve to remove

the nut

⑺

; after removing the bracket bolts, one person fixes the upper part of the crash bar with a 12# sleeve

Another person uses a 12# sleeve to remove the nut

⑸

. Then take out the left crash bar assembly and the right

crash bar assembly.

●

Right crash bar assembly

Remove the waterproof rubber plug

⑴

from the right crash bar assembly, and then pull out the right water tank

cover

⑽

from the round rubber

⑾

on the right crash bar

⑼

●

Left crash bar assembly

Pull out the left water tank cover

⒀

from the round rubber

⑾

on the left crash bar

⑿

4111200-007051 KD150

－

Z2 crash bar rubber mounting sleeve (dark

gray matte)

Summary of Contents for ZT125-Z2













































































Search results

Summary of Contents for ZT125-Z2

Reviews:

Related manuals for ZT125-Z2

Brands by name

Popular brands

Zontes ZT125-Z2, Service Manual

Search results

Summary of Contents for ZT125-Z2

Reviews:

Related manuals for ZT125-Z2

Brands by name

Popular brands