background image

H0408600 Rev C

English  |  Français  |  Español  

Jandy

®

 Pro Series

JE Heat Pump

installation and 

opEration Manual

WARNING

For Your saFEtY -

 This product must be installed by a licensed HVAC technician certified in heat 

pump repair and maintenance by the jurisdiction in which the product will be installed where such 
state or local requirements exists. The technician must possess and comply with all certifications and 

regulations regarding the purchasing, handling, transportation and reclamation of R410A refrigerant. 
In the event no such state or local requirement exists, the installer or maintainer must be a 
professional with sufficient experience in pool equipment installation and maintenance so that all of 
the instructions in this manual can be followed exactly. Before installing this product, read and follow 
all warning notices and instructions that accompany this product. Failure to follow warning notices 
and instructions may result in property damage, personal injury, or death. Improper installation and/
or operation can create an electrical hazard which can cause serious injury, property damage, or 
death. Improper installation and/or operation will void the warranty.

Summary of Contents for Jandy Pro Series JE1500T

































Reviews: