background image

5

807066 v1.00 03.21 HBP AB Install Instructions

WARNINGS & PRECAUTIONS

1.  For continued safety of this appliance it must be installed, operated and 

maintained in accordance with the manufacturer’s instructions.

2.  This appliance may deliver water at high temperature. Refer to the Plumbing Code 

of Australia (PCA), local requirements and installation instructions to determine if 

additional delivery temperature control is required.

3.  All plumbing and electrical connections must be made in accordance with local 

regulations and relevant standards. For Australia/NZ: electrical installation must 

comply with AS/NZS 3000. For Australia/NZ:, plumbing installation must comply with 

Plumbing standard AS/NZS 3500. UK: the system must be installed in accordance 

with water supply byelaws, current IEEE regulations and local authority byelaws.

4.  All installation and service work must be completed by trained and suitably 

qualified tradespeople. Faulty operation due to unqualified persons working on 

the product may void warranty coverage. 

5.     This appliance must be earthed. The resistance of the earth connection from 

each exposed metal part must be less than 1 ohm.

6.  The power cord and general power outlet must be in a safe and accessible 

position after installation. 

7.  Any disconnection to the fixed wiring must be in accordance with local 

regulations and relevant standards including AS/NZS 3000.

8.  Do not remove the cover of the appliance under any circumstances without first 

isolating the appliance from the power supply.

9.  The cold water supply to this appliance must be potable and fall within your local 

authority guidelines.

10.  The installer is responsible to supply and install all valves as required by local 

regulations and relevant standards. 

11.  In hard water areas where mineral scale accumulation may become a problem, 

consideration should be given to the maintenance required. A suitable form of 

water treatment may be necessary.

12.  This appliance is designed for indoor use and must not be installed outdoors or 

exposed to the elements of nature. 

13.  This appliance must operate within ambient temperatures of 5ºC - 50ºC. 
14.  Do not clean this appliance with a water jet.  Do not position this appliance in an 

area that may be cleaned by a water jet.

15.  This appliance is not intended for use by young children or infirm people without 

supervision. Young children should be prevented from having access to ensure 

that they are not able to use or play with the appliance. 

16.  This appliance is intended to be used in: staff kitchen areas in shops, offices and 

other working environments; farm houses and by clients in hotels, motels and 

other residential type environments; bed and breakfast type environments; 

catering and similar non-retail applications.

17.  Due to the process of continuous improvement, the manufacturer reserves the right 

to change details mentioned in this manual, without notice. Visit the website of the 

manufacturer/distributor to ensure you have the latest copy of this document.

Summary of Contents for Hydroboil Plus 3L





























Reviews: