background image

5

Installation instructions & user manual

9120-34379 v1.20 Okt 2022 - ZIP DCX Next

Technical support 

Tel: 0345 6 005 005 email: [email protected]  www.zipwater.co.uk

1. Description of the appliance

As soon as you open the hot water tap, the instantaneous water heater switches on 

auto ma ti cally. When the tap is  closed, the appliance automatically switches off. 

The E-convenience instant water heater DCX Next is a electronically controlled pres-

sure-resistant instantaneous water heater for an efficient water supply to one or more 

tap outlets .
Its electronic control regulates the power consumption depending on the selected 

outlet temperature, the respective inlet temperature and the flow rate, thus reaching 

the set temperature exactly to the degree and keeping it constant in case of water 

pressure fluctuations . The outlet temperature can be set to 35 °C, 38 °C, 42 °C, 48 °C 

or 55 °C using the central sensor key .
In case of a low feed temperature and a high flow rate at the same time, it could hap-

pen that the preset outlet temperature is not reached which is due to the fact that the 

appliance exceeded its capacity . The outlet temperature can be raised by reducing the 

water flow at the tap .
It is possible to use the instantaneous water heater in combination with an external 

load shedding relay for electronically controlled instantaneous water heaters (refer to 

installing instructions) .

2. Environment and recycling

Operation instruction

Note: Carefully read the enclosed safety instructions through in full before the appliance 

is installed, put into service and used and follow them in the further steps and during use!

 This product was manufactured climate neutrally according to Scope 1 + 2 . We recom-

mend the purchase of 100% green electricity to make the operation climate neutral as 

well . 

Disposal of old products: 

Your product was manufactured from high-quality, reusable 

materials and components . Products marked with the crossed-out wheeled bin sym-

bol must be disposed of separately from household waste at the end of their service 

life . Therefore, take this product to us as the manufacturer or to one of the municipal 

collection points that recycle used electronic devices . This proper disposal serves to 

protect the environment and prevents possible harmful effects on humans and the 

environment that could result from improper handling of the products at the end of 

their service life . For more detailed information on disposal, please contact your near-

est collection point or recycling centre or your local council .

Business customers:

 If you wish to discard equipment, please contact your dealer or 

supplier for further information .
For disposal outside Germany, please also observe the local regulations and laws .

Summary of Contents for InLine DCX Next





















Reviews: