TETHERED CONTROLLER MX32, RADIO CONTROLLER MX32FU Page 11
*)
LoR =
“Loco Recall” memory, in which all
previously active addresses are stored. Can
be opened with softkey III. More information
in the column to the right.
Rocker switch
Scrolling wheel
“Small” keys:
Switch between operating modes etc.
F
(next address
LoR
),
W
(
SWI
tches),
U
(Previous address
LoR
)
C
(delete visible address),
(Shift) higher functions
Speed slider
R- Key
(Direction)
S- Key
(Stop)
RG- Key
(Shunting)
LED yellow: Half- or 1/3 - speed
A- Key
(Enter
LOCO IN
)
E- Key
(
E-Screen
)
Function Keys
F0 ... F9
(= Numeric keys 1 … 0); with
(Shift) to the higher
F-Keys
An
“Address in use”
warning appears when the address is already active on a different controller. The address
can then, if desired, be taken over with the U-Key. Also see
“External & Computer Control”.
After activating the new address, that is, after switching over to the driving mode
LOCO
with the
F-Key
,
the loco can be
operated with the following controller elements
:
-
Slider for speed control
,
-
Scrollinging wheel
for fine speed control (+/- 12 steps from 128) or scrolling inside
LoR
, if open, or
volume control while function key is pressed.
-
Rocker switch
to browse inside the
LoR *),
if it is invisible (in the background).
-
R-Key
to change direction.
- Function keys
F0
… F9
(= the
numeric keys
1 … 0
),
- and
(Shift) key, for
F10 … F19
or
F20 … F28
;
back to
F0 ... F9
-
S-Key
, pressed briefly = emergency stop (if set as default in
CAB CONF
),
-
S-Key
, press/hold = broadcast stop (if set as default in
CAB CONF
),
-
S-Key
+
TP-Key
= track power OFF.
To activate
other locos:
A- Key
Switches to the
LOCO IN
display.
Enter new vehicle address.
F-Key
Activates
the new engine
(in this example without a name) and switches over to
the operating mode
LOCO
.
Softkey III
Show / hide Loco Recall (
LoR
)
The Loco Recall list opens in place of the function
icons and lists the vehicles currently stored in the
recall memory.
All vehicles that were activated once are
automatically entered into the
loco recall memory
(
LoR
) including their last valid GUI and driving data, so
they can be recalled and activated again when needed.
The LoR is also called “background memory”, from which
vehicles can be brought to the “foreground” by activating
them.
The LoR is also working when in the background,
that is, when it is NOT visible. Making it visible with
Softkey III offers a convenient overview and quick
selection using the scrolling wheel.
However, vehicles can be activated one by one from
the
LoR
with the F and U-Key, whether the
LoR
is
visible or
invisible
. Vehicles can be deleted from the
LoR
with the C-Key.
The open
LoR
shows for each vehicle:
Name, Address, Consist Info, Speed step or RailCom-Actual speed, Functions F0-F9, (after rocker
switch) Direction, MAN and Position.
III
F
NOTE: An accessory address can also be entered in
the
LOCO IN
display but is activated with
the
W- Key
instead of the F-Key.
See chapter
ACC LIST
!
ATTENTION
:
only possible if
LoR
is NOT displayed.
If
LOR
is displayed, switch with:
(Shift)
+ A-Key
LOCO IN
)
NOTE: By
tapping
the display areas (Name/Address, Picture, Speedo) different representations of
the
LOCO
screen are displayed, i.e. large picture (full width),
Name
in large font or
in full length
(full display width, but possibly dropping other components). See Chapter
“LOCO”.
