background image

 

 

Software and Firmware License Agreement  

 

ONCE  YOU  HAVE  READ  THIS  LICENSE  AGREEMENT  AND  AGREE  TO  ITS 
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED 
INTO  THE  ZHONE  PRODUCT.  BY  USING  THE  ZHONE  PRODUCT  YOU  SHOW 
YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT. 

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS 
LICENSE  AGREEMENT,  PROMPTLY  RETURN  THE  UNUSED  PRODUCT  IN  ITS 
ORIGINAL  PACKAGING  AND  YOUR  SALES  RECEIPT  OR  INVOICE  TO  THE 
LOCATION WHERE YOU OBTAINED THE ZHONE PRODUCT OR THE LOCATION 
FROM  WHICH  IT  WAS  SHIPPED  TO  YOU,  AS  APPLICABLE,  AND  YOU  WILL 
RECEIVE A REFUND OR CREDIT FOR THE ZHONE PRODUCT PURCHASED BY 
YOU. 

 

The terms and conditions of this License Agreement (the “Agreement”) will apply to the 
software and/or firmware (individually or collectively the “Software”) incorporated into 
the Zhone product (the “Product”) purchased by you and any derivatives obtained from 
the Software, including any copy of either. If you have executed a separate written 
agreement covering the Software supplied to you under this purchase, such separate 
written agreement shall govern. 

Zhone Technologies, Inc (“Zhone”) grants to you, and you (“Licensee”) agree to accept 
a personal, non-transferable, non-exclusive, right (without the right to sublicense) to 
use the Software, solely as it is intended and solely as incorporated in the Product 
purchased from Zhone or its authorized distributor or reseller under the following terms 
and conditions: 

  1.  Ownership: The Software is the sole property of Zhone and/or its licensors. The 

Licensee acquires no title, right or interest in the Software other than the license 
granted under this Agreement. 

  2.  Licensee shall not use the Software in any country other than the country in which 

the Product was rightfully purchased except upon prior written notice to Zhone and 
an agreement in writing to additional terms. 

  3.  The Licensee shall not reverse engineer, decompile or disassemble the Software 

in whole or in part. 

  4.  The Licensee shall not copy the Software except for a single archival copy. 

Summary of Contents for ETHX-DS3-1-LT





























Reviews: