GB | 29
Switching on/off
To switch on:
Push the on/ off switch (13)
Continuous operation: (fig. 9)
Secure the on/off switch (13) with the locking button (6)
To switch off:
Press the on/off switch (13) briefly.
Adjusting the oscillation rate (fig.
8)
Before you start working, adjust the oscillation rate ac-
cording to the application. Use a low number of oscil-
lations for rough grinding, increase the oscillation rate
for fine work.
Adjust the oscillation rate by pressing the button (5).
• Press the
button to increase the oscillation rate
(fig. 8).
• Press the
button to decrease the oscillation rate
(fig. 8).
Note:
The insertion tool moves for a short while after
having it switched off. Do not put aside the power tool
until the insertion tool has come to a complete halt.
Grinding
1. Attach an appropriate abrasive sheet (16) and se-
lect the corresponding speed.
2. Hold the power tool securely at the handle surfac-
es (7, 2) and switch it on as described.
3. Wait until the insertion tool has reached its full
operating speed.
4. Hold the grinding plate (1) as parallel as possible
to the wall, and touch the surface to be processed
with the brush edge first.
5. Apply some pressure to the grinding head (1) such
that the insertion tool touches the surface to be
processed.
6. Constantly move the power tool over the surface.
Note:
lf you want to avoid irregular grinding results,
do not keep the power tool at one spot for too long.
7. Lift the grinding plate (1) from the surface to be
processed before switching off the power tool.
8. Do not put aside the power tool until the insertion
tool has come to a complete halt.
When working with this power tool, a Iot of dust is
generated. The dust extraction unit is very useful if
you want to keep your workplace clean. lt is possible
to combine the extraction system or a vacuum cleaner
with the extraction hose (14) which is connected to the
adapter for dust extraction.
Insert the hose adaptor (15) into the connection for dust
extraction (10 or 12) and lock it by twisting as shown in
fig. 5 and 6.
Note: Connect your tool to an extraction unit or vacuum
cleaner. This will provide excellent extraction of dust
and debris.
m
Attention! For health safety reasons it is imperative
that you use a dust extractor.
Note:
Make sure that the vacuum cleaner is suitable
for being used together with a power tool.
Brush edge
The grinding head of this power tool is enclosed by a
brush edge which offers the following two advantages:
a) The brush edge protrudes beyond the grinding
plate (1) and touches the surface to be processed
first. Thus, the grinding plate is positioned in par
-
allel to the working area before the insertion tool
comes in contact with the surface which is to be
processed. This is to prevent the formation of
sickle-shaped recesses caused by the grinding
disk edge.
b) Furthermore, the brush edge prevents the gener-
ation of excessive dust. Dust generated during the
grinding process is not transported towards the
outside but is removed by the extraction system.
Make sure before each operation with this power
tool that the brush edge is not damaged. Have it
replaced if there is damage or wear.
Connection to the power supply
1.
Make sure that the power tool is switched off. Al
-
ways switch the on/off switch (13) to off position
before connecting the power tool to the power
supply.
2. Plug the power plug into a correctly installed sock-
et which complies with the requirements specified
in the technical data.
3. Your power tool is now ready for operation.
Summary of Contents for 935-33
