28 | GB
• The power tool may only be operated in suitable
rooms (well ventilated).
8. Attachment and operation
Installation (fig.
2-3)
-
Fold the front and back part together. And then tight-
en the Set Screw (3).
Fitting the telescopic extension (fig. 4)
Insert the telescopic extension (11) into the connection
for the telescopic extension (12) and lock it by twisting
as shown in fig. 4.
Note:
Adjust the Telescopic Plasterboard Sander with
the telescopic extension (11) so that you can work with
it most comfortably. The machine can also be used
without telescopic extension.
Sandpaper
Selection
1.
The grain size of the sandpaper is specified on its
rear side. The smaller the specified number, the
coarser the graining.
2. Use sandpaper with coarse grain for rough grind-
ing, and sandpaper with fine grain for finishing.
We recommend sandpapers with aluminium ox-
ide, silicon carbide or other synthetic abrasives.
3.
lf you can chose between sandpapers with differ
-
ent graining, you should start with coarse grain-
ing sandpaper and complete the grinding process
with the finest possible graining. Thus you will get
good and smooth grinding results.
How to apply and replace sandpaper
1. Apply the sandpaper (16) to the grinding plate (1)
using the Velcro strip mechanism.
2. Align the sandpaper (16) with the grinding plate
(1) and press it on evenly.
3.
PuIl the sandpaper (16) off the grinding plate (1)
and replace it with a new one / another one (fig. 7).
Dust extraction
WARNING! Harmfull noxious gases may be gener-
ated when e.g. lead-containing paint is processed.
These gases entail a risk for the operator and the
persons in the vicinity!
Therefore only use the power tool in combination
with a dust extraction unit, and protect yourself
and other persons in the working area with ad-
ditional suitable personal protective equipment!
The specified hand-arm vibration value is based on
grinding with an abrasive sheet. Different applications
may result in different values.
The noise and vibration values were determined ac-
cording to EN 60745-1 and EN 60745-2-3.
The specified vibration value was measured an the
basis of a standard test method and can be used to
compare any kind of power tools.
The specified vibration value can also be used for the
initial evaluation of exposure.
Warning! Depending on how you use the power
tool, the actual vibration values may deviate from
the specified values!
Take measures to protect yourself against vibra-
tions! Make sure to take into account the entire
work process, i.e. also times when the power tool
is operated without Ioad or switched off! Appro
-
priate measures include the regular maintenance
and care of the power tool and its attachments,
keeping your hands warm, regular breaks and well
planned work processes!
Wear hearing protection.
The effects of noise can cause a loss of hearing.
7. Before starting the equipment
Open the packaging and remove the device carefully.
Remove the packaging material as well as the packag-
ing and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage.
If possible, store the packaging until the warranty pe-
riod has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal
-
lowing and suffocation!
Before you connect the equipment to the mains supply
make sure that the data on the rating plate are identical
to the mains data.
• Report any damage immediately to the transport
company which was used to deliver the power tool.
• Avoid long supply lines (extension cables).
• Do not operate the power tool in a damp or wet room.
Summary of Contents for 935-33
