background image

zero

HOME AUTOMATION

PG13

ZCOM230 |CONTROL PANEL | COMANDO 230V

ZCOMV2 |CONTROL PANEL | COMMANDO 24V

Discovering the origin of the problem

1.  Open  control  board  and 

check if   it   has   230V   power   

supply

2. Check input fuses

3. Disconnect the motor from 

control  board  and  test  them 

by  connecting  directly  to 

power supply in order to find 

out if they have problems.

4. If the motor works, the pro

-

blem is on the control board. 

Pull it out and send it to our 

ZERO technical services for 

diagnosis.

5. If the motor doesn’t work, 

remove them from installation 

site and send to our ZERO te-

chnical services for diagnosis.

Check all motion axis and associated motion systems related with the motor and the gate to find out what is the problem.

1.  Check  capacitors,  testing 

operator  with new capacitors;

2. If capacitors are not the 

problem,  disconnect  motors 

from control  board  and  test  

them by connecting directly to 

power supply in order to find 

out if they have problems. 

3. If the motors work, the pro

-

blem  is  from  control  board. 

Pull it out and send it to our 

ZERO technical services for 

diagnosis;

4. If the motors doesn’t work, 

remove them from installation 

site and send to our ZERO te-

chnical services for diagnosis

All ZERO   control  boards have LEDs that easily allow to conclude which devices are with anomalies. All safety devices LEDs 

(DS) in normal situations remain On. All “START” circuits LEDs in normal situations remain Off.

If LEDs devices are not all On, there is some security systems malfunction   (photocells, safety edges), etc.

1 • Close with a shunt all safety systems on the control board (check manual of the control board in question). If the automa

-

ted system starts working normally check for  the problematic device. 

2 • Remove one shunt at a time until you find the malfunction device  .

3 • Replace it for a functional device and check if the motor works correctly with all the other devices. If you find another one 

defective, follow the same steps until you find all the problems.

If  “START” circuits LEDs are turn On, there is a control device sending permanent signal.

1 • Disconnect all wires from START terminal input (terminal 3).

2 • If the LED turned Off, try reconnecting one device at  a time until you find the defective device.

In case described procedures fell, remove control board and sendto our technical services for diagnosis.

Check all motion axis and associated motion systems related with the motor and the gate to find out what is the problem.

1.  Check  capacitors,  testing 

with new  capacitors;

2. If capacitors are not the 

problem,  disconnect  motor 

from  control  board  and  test 

it  by  connecting  directly  to 

power supply in order to find 

out if it is broken;                                       

3. If the motor doesn’t work, 

remove  it  from  installation 

site and send to our ZERO te-

chnical services for diagnosis.

4.  If  motor  work  well  and 

move gate at full force during 

the    entire  course,  the  pro

-

blem  is  from  controller.  Set 

force using trimmer on the 

board.  Make  a  new    working  

time  programming,  giving 

suffient time for opening and 

closing with appropriate force.

5. If this doesn’t work, remo

-

ve control unit and send it to 

ZERO technical services servi-

ces.

NOTE: Setting force of the controller  should  be  sufficient to make the gate open and close without stopping, but should stop 

and invert with a little effort from a person. In case of safety systems failure, the gate shall never cause physical damaged to 

obstacles (vehicles, people, etc.).

Summary of Contents for COMANDO 230V

















Reviews: