background image

 

NOTICE TO PURCHASERS AND USERS OF OUR PRODUCTS 

AND THIS INFORMATIONAL MATERIAL

 

 

Clemco proudly provides products for the abrasive blast industry and 
is confident that industry professionals will use their knowledge and 
expertise for the safe and efficient use of these products.

 

 

The  products  described  in  this  material  and  the  information relating 
to  these  products  are  intended  for  knowledgeable,  experienced 
users.  It  is  the  responsibility  of  the  employer  to  ensure  that  proper 
training  of  operators  has  been  performed  and  a  safe  work 
environment is provided.

 

 

No  representation  is  intended  or  made  as  to  the  suitability  of  the 
products  described  here  for  any  purpose  or  application,  or  to  the 
efficiency,  production  rate,  or  useful  life  of  these  products.  All 
estimates regarding production rates or finishes are the responsibility 
of  the  user  and  must  be  derived  solely  from  the  user’s  experience 
and expertise, not from information contained in this material.

 

 

It  is  possible  that  the  products  described  in  this  material  may  be 
combined  with  other  products  by  the  user  for  purposes  determined 
solely  by  the  user.  No  representations  are  intended  or  made  as  to 
the  suitability  of,  engineering  balance  of,  or  compliance  with 
regulations or standard practice of any such combination of products 
or components the user may employ.

 

 

This  equipment  is  only  one  component  of  a  cabinet  blasting 
operation.  Other  products,  such  as  air  compressors,  air  filters  and 
receivers,  abrasives,  equipment  for  ventilating  or  dehumidifying,  or 
other  equipment,  even  if  offered  by  Clemco,  may  have  been 
manufactured  or  supplied  by  others.  The  information  Clemco 
provides  is  intended  to  support  the  products  Clemco  manufactures. 
Users must contact each manufacturer and supplier of products used 
in  the  blast  operation  for  warnings,  information,  training,  and 
instruction relating to the proper and safe use of their equipment.

 

BNP

®

 Suction Blast Cabinets

Models 6012 and 7212

O. M. 27723

DATE OF ISSUE:  05/94 
REVISION: 

B, 04/19 

 

© 2019 CLEMCO INDUSTRIES CORP. 

One Cable Car Dr. 

Washington, MO 63090 

Phone (636) 239-4300 

Fax

 

(800)

 

726-7559 

Email: [email protected] 

www.clemcoindustries.com 

Summary of Contents for BNP 6012








































Reviews: