background image

Page 4 of 20

Zenith Hydro Tap Installation and Operating Instructions - 81467 - February 2005

These Installation Instructions cover the entire Zenith HydroTap range. Use the
chart on the left to identify the model you are using:

Commercial and Domestic Models:

BC

= Boiling and Chilled, Filtered, Timer

BF = 

Boiling, Filtered

BD  = Boiling and Ambient Filtered
B    = Boiling only (unfiltered)
D    = Disabled Lever controls, (Optional order only)
HT

= Domestic Models (boiling only are unfiltered, boiling/chilled are filtered) 

Boiling Water Capacity:

100 = 100 cups in one hour   150 = 150 cups in one hour

Chilled  Water Capacity: (BC only)

125 = 125 glasses in one hour   175 = 175 glasses in one hour

Filtration:  (BC, BD and BF only)
Note:

The

Cup

measurement = 167mls, the 

Glass

measurement = 200mls.

Models covered by these instructions

Before installing ensure that the following have been provided at the
installation site:

Sufficient space in the cupboard to install the undersink unit in accordance
with these Installation Instructions. A table of dimensions is given below.

NOTE: Add 65mm to the Depth to the under-sink unit to allow for Water and Electrical connections

A water supply connection with isolating valve inside the cupboard within
reach of the 750 mm flexible connection and positioned so that the
connection point and the stop cock will not be obstructed when the
undersink unit is installed.

Power supply 220-240 Volt AC, for connection to the heater via a 10 amp
G.P.O.

Installation Requirements

BC

Model

100

Cups of

Boiling Water

per Hour

125

Glasses of

Chilled Water

per Hour

Frost Protection

If this appliance is located where the ambient air temperature could fall below 5ºC
when the heater is not in use, do not turn off the appliance electrically. This
safeguard does not offer the same protection to the connecting pipework and
fittings.

Installation Environment Considerations

This unit is intended for indoor use only and should never be installed outdoors
or exposed to the elements of nature. This unit must not be positioned in an
area that may be cleaned by a water jet. This unit must not be cleaned by a
water jet.

#

Section Heading

#

Section Heading

Read These Warnings First 

continued

Height

mm (inch)

Depth

mm (inch)

Weight empty

kg’s  lbs

Weight full 

kg’s  lbs

337 (13.2)

430 (16.9)

440 (17.3)

28  (61.7)

34.5 (76)

337 (13.2)

430 (16.9)

28  (61.7)

35 (77.1)

395 (15.5)

465 (18.3)

500 (19.6)

29.5  (65)

38 (83.7)

409 (16.1)

340 (13.3)

321 (12.6)

10   (22)

14 (30.8)

353 (13.8)

320 (12.5)

9.5  (20.9)

12 (26.4)

353 (13.8)

320 (12.5)

290 (11.4)

9  (19.8)

11.5 (25.3)

353 (13.8)

320 (12.5)

9  (19.8)

Width

mm (inch)

440 (17.3)

290 (11.4)

290 (11.4)

11.5 (25.3)

Model

BC & HT 60/85 

BC 100/125 

BC 150/175 

B 150 

B 100 

B 60 

BD 60 

Summary of Contents for HYDROTAP 30009





















Reviews: