FACTORY MENU
3828VD0171G
2-11
DIGITAL FCS - FACTORY MENU
181-F GCMON: Progressive picture improvement.
0=off.
182-F HSPPL: H sync shift. Default value is 0
183-F VSLPF: V sync shift. Default value is 0
184-F CVSEL1: Output select for CVBS2.
185-F CVSEL2: Output select for CVBS4 or Y.
186-F CLMPSIG1: Clamping signals ADC1. 0=1
st
color
decoder.
187-F YCTOCOMB: YC to Comb filter. 0=Normal op-
eration.
188-F VDG: Vertical difference gain. 1=medium2
189-F HDG: Horizontal difference gain. 2=medium2
190-F DDR: Diagonal dot reduction. 1=medium1
191-F COR: Vertical peaking coring. 0=disabled
192-F NOSEL: Notch filter select. 3=max peaked.
193-F DCR: Vertical peakigDC rejection filter.
0=disabled.
194-F VPK: Vertical peaking gain. 0= NO VPK.
195-F LINLENH60: Number of pixels for 60HZ. De-
fault value is 3.
196-F DISCOMB: Disable comb filter. Depending
video source selected.
197-F HWID: Minimum width of H sync. Default
value is 0.
198-F FION: Increment freeze before V sync. 0= no
freeze.
199-F PPLIP_H: Default value is 2.
200-F PPLIP_L: Pixel per line. Default value is 0.
201-F TO1RGB: YUV output selection. Default value
is 0.
202-F BLANDEL: Delay in pixels from h sync. De-
fault value is 0 (no delay).
203-F VBLANPOL: Vertical blanking signal polar-
ity. 0= positive.
204-F HOUTPOL: Horizontal output polarity. 0=
high active.
205-F VOUTPOL: Vertical output polarity. 0=high
active.
206-F BLANPOL: Blank polarity. 0=high active.
207-F VBLANDEL_95: Vertical delay in lines from
in v sync. Default value is 0.
208-F BLANLEN_H: Default value is 0.
209-F BLANLEN_L: Default value is 0.
210-F VBLANDEL_40: Vertical length in lines from
start of active blank signal. Default value is 0.
211-F VBLANLEN_H: Vertical length in lines from
start of active blank signal. Default value is 0.
212-F VBLANLEN_L: Vertical length in lines from
start of active blank signal. Default value is 0.
213-F PKLY: Voltage level for Y DAC output. De-
fault value is 237d.
214-F PKLU: Voltage level for U DAC output. De-
fault value is 254d.
215-F COARSEDEL: Luminance coarse delay output.
Default value is 5d.
216-F FINEDEL: Luminance fine delay output. De-
fault value is 0.
217-F PKLV: Voltage level for V DAC output. De-
fault value is 254d.
218-F MDVFON: Default value is 1.
219-F FM-RES: Default values is 0.
220-F FM-THYON: Default value is 0.
221-F FM-THRON: Default value is 1.
222-F FMATH: Default value is 0.
223-F FMDTH: Default value is 15.
TDA4887 NTSC
224-F RGAIN CTRL NTSC: Red gain control is used
for white point adjustment. Range: 0-255d.
225-F GGAIN CTRL NTSC: Green gain control is
used for white point adjustment. Range:0-255d.
226-F BGAIN CTRL NTSC: Blue gain control is used
for white point adjustment. Range: 0-255d.
