background image

6

806310NZ v1.06 08.19 CW ChillMaster & EconoMaster

Never use strong, corrosive or abrasive cleaning materials. Stainless steel surfaces 
will show scratches if an abrasive cleaning product is used.

Wipe clean the outer surfaces with a sponge or a soft cloth using a mild soap and 
water.

The louvres on the sides of the unit need to be kept free of dust and lint to permit 
free flow of air through the vents. Check at least monthly, and dust or vacuum if 
required.

Cleaning

There are dangerous voltages present within the unit. All service work must only be 
carried out by a suitably qualified and experienced service person.

Before calling for service, check that both the water and electricity supplies are 
turned ‘ON’ and OK.

Call a licenced electrician, plumber, or Zenith free call in New Zealand on 0800 558 
055, for assistance, service, spare parts, or enquiries.

Filter Timer Module (ChillMaster only)

The filter timer module is a microcontroller-programmable, extended duration 
timer. It is programmable from one to six months in duration.
A red Light Emitting Diode (LED) that shows through the front label will flash once 
per second when the selected filter time has elapsed, as a reminder to replace the 
filter. The unit will stay in this state until the batteries are exhausted.
The 2x AAA batteries should be replaced when filter is replaced.
To reprogram the filter timer module, first remove the front panel of the 
ChillMaster. The filter timer module is located inside.
Remove the batteries and locate the switch bank, mounted on the reverse side to 
the battery holder of the timer module’s printed circuit board.
Referring to the table below, select the appropriate sequence. Set the switches to 
ON or OFF positions by depressing the end of each switch with a small instrument 
such as a pen or small screw driver.
Replace the batteries and the front panel of the ChillMaster.

Note:

 Factory Setting is 6 months

TIME 

MONTHS

SWITCH 1

SWITCH 2

SWITCH 3

SWITCH 4

1

ON

OFF

OFF

OFF

2

OFF

ON

OFF

OFF

3

ON

ON

OFF

OFF

4

OFF

OFF

ON

OFF

5

ON

OFF

ON

OFF

6

OFF

ON

ON

OFF

TEST

X

X

X

ON

(X = Any position)

Servicing

Summary of Contents for ChillMaster









Reviews: