10
HINT
Information on the product and
hints on its use
●
This appliance is intended for domestic use only.
●
Unplug the appliance after you finish using it. Put away
the cord, pushing it gently through the opening and
place the plug in the compartment.
●
If the appliance cannot be switched on, bring it to
a service centre.
●
Separate the meat to be minced from bones, sinews,
gristles and veins.
●
Cut large portions of the product into smaller pieces
before mincing.
●
Do not grind dry poppy seed. The poppy seed must
be scalded and soaked for dozen or so hours before
mincing.
●
Use a soft brush for cleaning the metal parts.
●
Do not wash the metal parts in dishwashers. Abrasive
detergents used in dishwashers may cause the metal
parts to become dark. Wash them manually using
traditional washing-up liquids.
Technical parameters
The technical parameters are indicated on the rating label.
Permissible duration of uninterrupted operation 15 minutes.
Break before the next use
30 minutes.
Noise level (L
WA
)
77 dB/A.
MBP – Motor Blocked Power
2000 W
Description
The food mincer consists of:
1
Mincer motor – each motor is adapted to install each
ZELMER mincing unit, citrus juicer, juicer, coffee grinder
and shredder.
1a
On/Off button
1b
„Reverse” switch
1c
Lock button
The mincer unit consists of:
2
Mincer body
3
Scroll with clutch
4
Double-side cutter
5
Mincer screen with 4 mm openings
6
Ring nut
7
Food tray
8
Pusher
And additional accessories:
9
Base plate
10
Sausage filler nozzle
11
Mincer screen with 8 mm openings
12
Mincer screen with 2,7 mm openings
A
Mechanical safety device for the motor
13
Scroll
14
Clutch
15
Screw M4X20
The mincer is equipped with a mechanical safeguard, which
protects the motor against damage – the teeth in the clutch
break when the mincer is overloaded (e.g. when bones get
inside).
Replace the damaged clutch:
●
twist off the screw
(15)
from the scroll with the damaged
clutch,
●
remove the damaged clutch
(14)
,
●
attach the new clutch and tighten it with the screw
(15)
.
„Reverse” function
The motor has a special function allowing to temporarily
change the direction of the scroll. It is used if mincing is
limited and/or if there is too much product in the mincer body
(the scroll does not take the product). Press the
„
R”
switch
for a short period of time, the product will be removed from
the inside of the mincer body. Press the
„I”
button once
again to continue operation.
If the scroll is still blocked by the excess of product, use the
„R”
switch once again, remove the product from the mincer
body and next remove product parts which make it difficult to
mince (e.g. sinews, etc.).
In some cases it is necessary to dismantle the mincer body
and remove the above-mentioned obstacles.
Working with the mincer unit
Insert the following parts into the mincer body
(2)
:
1
Insert the scroll
(3)
with the coupling facing inside.
2
Fit the knife
(4)
onto the pin of the scroll
(3)
.
3
Place the screen
(e.g. 5)
over the knife so that the
protrusion in the mincer body will fit into the groove in the
circumference of the screen.
4
Tightly fit all the elements of the mincer unit.
5
Fit the assembled mincer unit onto the drive unit
(1)
and
turn it until you hear a click of the lock. It means that the body
has been properly installed.
6
Place the tray
(7)
on the mincer body
(2)
.
Preparing the appliance for operation
and switching on the appliance
●
Take out a sufficient length of the supply cord and the
appropriate accessories from the compartment.
1
Place the motor
(1)
near the socket, on a hard, stable
surface. Do not cover the ventilation openings of the housing.
●
Open the compartment on the back of the housing and
take out an appropriate screen
(Fig.
B
)
.
A screen with 4 mm openings is installed in the
mincer body as a standard.
A
D
C
